manualshive.com logo in svg

Farm King 2400, Operator And Parts Manual, Page: 25 / 112

Share
Download
Farm King 2400 Operator And Parts Manual Download Page 25

25

Assembly - Round Bale Carrier 2400

Figure 4

Align and install the outer light bracket (Item 1) 

[Figure 4]

under the inner light bracket.

Install one 1/2” flat washer on a 1/2” x 2” bolt (Item 2)

[Figure 4]

, then install the bolt down through the inner

light bracket and outer light bracket. Install one 1/2” flat
washer and 1/2” locknut on the bolt. Tighten bolt and
locknut until the two light brackets make contact.

NOTE: Outer light bracket should be able to be

rotated in toward the carrier frame. Do Not
over-tighten.

Repeat procedure for LH outer light bracket.

Figure 5

Align and install the RH tail light (Item 1) 

[Figure 5]

(Amber lens to the outside) under the outer light bracket.

Install four 1/4” x 1” bolts (Item 2) 

[Figure 5]

 down

through the outer light bracket and tail light. Install one 1/
4” locknut on each bolt. Tighten bolt and locknut. Do Not
over-tighten.

Repeat procedure for LH outer light bracket.

Figure 6

Connect the LH & RH tail light pigtail harnesses to the
enhanced ag lighting module electrical harness 

[Figure

6]

.

B-10017

1

2

B-10018

1

2

B-10019

Summary of Contents for 2400

















































































































Reviews:

No comments