background image

10 

Set Low Fuel Alarm 

 

To set the Low Fuel alarm, press 

key 

 

until 

ALr

 is displayed  

 

After 2 seconds, the current alarm value is 
displayed. 

 

If no alarm value has been entered, 

OFF

 

is displayed 

Press and hold both keys for 2 seconds 
until the display flashes. 

 

Use the up or down keys to change the 
value.  

     or    

 

Press and hold both keys for 2 seconds to 
save this new value to memory and exit 
this function. 

ALr

 is displayed and then the new value 

with an arrow pointing at the alarm bell. 

 

When the fuel remaining value 
drops below the fuel alarm value, 
the alarm sounds and the alarm 
arrow flashes.  

 

Press any key to mute the alarm. 
The alarm arrow continues to flash 
as long as the alarm condition 
remains. 

Reset TRIP LOGs 

To reset a log, press the 

key 

until the display indicates the name 
of the log to be reset.  

Press and hold both keys for 2 
seconds.  

 

The display shows trP or tot or for 2 
seconds before resetting to zero. 

 

The trip log value may be reset 
without changing the total log 
value. if the total log is reset to 
zero, then the trip log will 
automatically reset to zero. 

Note: If the total log exceeds 999 
then both it and the trip log will 
be reset to zero. 

Summary of Contents for IS0125













Reviews: