manualshive.com logo in svg

Faria Commander, Owner'S Manual

Share
Download
Faria Commander Owner'S Manual Download Page 3

Installation:

CAUTION:

 Disconnect the battery during 

installation.  Tighten  nuts  on  the 

backclamp  only  slightly  more  than  you 

can  tighten  with  your  fingers. 

Six  inch-

pounds

  of  torque  are  sufficient.  Over-

tightening  could  result  in  damage  to  the 

instrument and may void your warranty.

1. Cut a 3-3/8” diameter hole

 in the dash 

and mount the gauge with the backclamp 

supplied.
Follow  the  enclosed  instructions  for 

installing  the  sender.  Once  the  sender  is 

installed  and  you  have  run  the  cables  to 

the  Commander,  connect  the  wires  from 

the  sender  to  the  corresponding  Small  or 

Large  connectors  as  illustrated  using  the 

butt  connectors  supplied.  The  butt 

connectors  have  a  heat  activated 

waterproofing.  Once  the  butt  connections 

have been crimped slowly apply heat with 

a heat gun until you see sealant coming 

out  of  the  connector  ends.  It  is 

recommended  to  wrap  the  connections 

together  with  electrical  tape  for  further 

protection.

2. Small  Connector Socket
Tachometer with Fuel Flow

Follow  the  wiring  diagram  at  the  end  of 

this  manual  for  wiring  connections. 

HN0356.

SystemCheck® connections can be found 

on HN0358.

Tachometer  with  Ambient  Air  and 

Water Temperature.

Follow  the  wiring  diagram  at  the  end  of 

this  manual  for  wiring  connections. 

HN0355.

3. Large  Connector Socket
Tachometer with Fuel Flow

Follow  the  wiring  diagram  at  the  end  of 

this  manual  for  wiring  connections. 

HN0354. 

SystemCheck® connections can be found 

on HN0358.

Tachometer  with  Ambient  Air  and 

Water Temperature.

Follow  the  wiring  diagram  at  the  end  of 

this  manual  for  wiring  connections. 

HN0355  or  HN0372  for  5  inch 

Commanders..

Used for all splices.

Wires

Heat Shrink Tube

(red or blue)

Metal Butt Connector

(red or blue).

Used for all splices.

Larger

Connector

 Socket

Smaller

Connector

Socket

Small

Plug

Large 

Plug  

Note: For wiring

diagram for the 

Large Connector

Plug see HN0354

SystemCheck HN0358

or HN0355 for 

Temperature senders.

HN0372 for 5 inch

Commanders.

Note: For wiring

diagram for the 

Small Connector

Plug see HN0356

SystemCheck HN0358

or HN0355 for Temperature senders.

Page 1

Harness HN0354 

Large Connector

Large Plug

(CN0082)

To Commander

Shrink Tubing
or Wrap

Green

Pin A   Red 

Fuel Flow Power

Pin B 

Green  Sender  Grounds

Pin C 

White  Fuel Flow Signal

Pin D 

Pink 

Fuel Tank Level

ECR 1903 12/21/01

(Tank Sender Ground)

(Sender Ground)

(Sender Power)

(Sender Signal)

Fuel Flow Transducer

Pink

(Fuel Level)

White

White

Red

Black

Green Shield

Page 17

This manual for 4 or 5 inch Commanders 

with 

1) Tach/Hour/Fuel Flow.

2) Tach/Hour/SystemCheck®/Fuel Flow.

3) Tach/Hour/Ambient Air/Water

  Temperature.

All manuals and user guides at all-guides.com

Summary of Contents for Commander























Reviews:

No comments

Brands by name

Popular brands

Load more brands