Fanvil A1 User Manual Download

Page: 28 / 50

Edition RFC3323and

RFC3325;

Subscribe Expire

Time

Overtime of resending subscribe packet. Suggest

using the default config.

Enable Conference

number

Set to use sever conference.

MWI Number

Input the number of the server's voice-mail box

Click to Talk

Set click to Talk (need practical software support).

Signal Encode

Enable/Disable Signal Encrypt.

RTP Encode

Enable/Disable RTP Encrypt.

Enable Session

Timer

Set Enable/Disable Session Timer, whether support

RFC4028.It will refresh the SIP sessions.

Answer With

Single Codec

Enable/Disable the function when call is incoming,

phone replies SIP message with just one codec

which phone supports.

Auto TCP

Set to use automatically TCP protocol to guarantee

usability of transport as message is above 1300

byte

Enable Strict Proxy Support the special SIP server-when phone receives

the packets sent from server

，

phone will use the

source IP address, not the address in via field.

Enable GRUU

Set to support GRUU

Enable Display

name Quote

Set to make quotation mark to display name as the

phone sends out signal, in order to be compatible

with server.

5.3.3.2. Stun Config

In this web page, you can config SIP STUN.

STUN:

By STUN server, the gateway in private network could know the type of NAT and

the NAT mapping IP and port of SIP. The gateway might register itself to SIP server

with global IP and port to realize the device both calling and being called in private

network.

Summary of Contents for A1



















































Search results

Summary of Contents for A1

Reviews:

Related manuals for A1

Brands by name

Popular brands

Fanvil A1, User Manual

Search results

Summary of Contents for A1

Reviews:

Related manuals for A1

Brands by name

Popular brands