manualshive.com logo in svg

Fantasea FSD-1100, Operator'S Manual

Share
Download
Fantasea FSD-1100 Operator'S Manual Download Page 16

 

16 

 

USING THE FLASH 

The PowerShot has a built-in flash, which will illuminate nearby underwater subjects. For subjects that are 

farther away, an accessory slave flash is recommended (see below).  A built-in flash diffuser is supplied 

which will help achieve a wider and softer light source thereby providing more coverage and less likelihood 

of 

backscatter (

the unattractive snowstorm affect of the flash reflecting off the suspended particles in the 

water). Further reduction of 

backscatter 

can be achieved by using an accessory off-camera slave flash. This 

will be discussed in more detail later. 

The need for artificial light to maximize color reproduction is necessary in nearly all pictures. Therefore it is 

strongly recommended that you set the flash mode to 

Flash Always

. This will ensure the flash fires on every 

exposure regardless of the ambient light conditions (Please refer to the camera's

 

instruction manual for more 

details).  

Outdoor photographers do not have this same problem. There is no backscatter to be concerned with, and due 

to the ability of the flash to travel farther and more effectively in air as compared to in water, there is 

normally not a need for an accessory flash to provide proper illumination for most subjects. 

 

ACCESSORY SLAVE FLASH 

If you use the PowerShot built-in flash as the master, you can trigger a second 

slave 

flash to provide more 

artificial light when needed. To do this, you must use an accessory flash that has a 

slave 

feature built in. The 

flash from the PowerShot must be aimed or bounced towards the accessory flash's 

slave 

sensor, or other fiber 

optic sensor. This will trigger the slave to fire in sync with the master flash.  

When using an accessory slave flash with fiber optic cable, it is recommended to black out the internal 

camera flash.  The internal flash is located near the camera lens and can contribute to backscatter by 

illuminating floating particles close to the lens port or a shadowing effect caused by the lens port. 

If the sensor of the fiber optic cable is attached to the outside of the housing directly above the internal flash 

and taped over with black tape- it will block out the light from the internal flash but transmit the light pulse to 

the external slave flash 

 

Note  

Be sure to use a slave flash that has the ability to ignore the built-in pre-flash in 

digital cameras, and synchronizes with the shutter release. 

 

Summary of Contents for FSD-1100






















Reviews:

No comments

Brands by name

Popular brands

Load more brands