Fanimation FP8050 The Quattro Owner'S Manual Download

Page: 13 / 14

NOTE:

The illustration shown is not to scale or its actual configurations may vary.

Part

Description

Part #

Fan Motor Assembly

Hanger Bracket with Screws

Hanger Ball/Downrod Assembly

Ceiling Canopy

Canopy Screw Cover

Motor Coupling Cover

Blade Set

Upper Light Kit Plate

Light Bulb GU10, 50W

Lower Light Kit Cover

Receiver Unit

Hand-Held Remote Control

Blade Balancing Kit

Bag Assembly - Loose Parts:

Wire Connector (4)

Washer Head Screw,

3/16-24 x 12.5mm (13)

Fiber Washer, 3/16” (13)

—
—

—

4” Phillips Head Screwdriver

—

AMA8050**

APGAC110RBL

ADRAC1-45**

P805001**

APPAC1101**

AP1115**

AP805005**

P805006CH

PPGU10B50

AP805008**

RECAN44

C24

BALKT

HDWFP8050**

Parts List

** Insert FINISH CODE

(Refer to fan model number located on downrod support)

HOW TO ORDER REPAIR PARTS

When ordering repair parts, always give the

following information:

•

Part Number

•

Part Description

•

Fan Model Number

Contact your retail store for repair parts.

Before discarding packaging material, be certain all parts have been removed.

Summary of Contents for FP8050 The Quattro















Search results

Summary of Contents for FP8050 The Quattro

Reviews:

Related manuals for FP8050 The Quattro

Brands by name

Popular brands

Fanimation FP8050 The Quattro, Owner'S Manual

Search results

Summary of Contents for FP8050 The Quattro

Reviews:

Related manuals for FP8050 The Quattro

Brands by name

Popular brands