background image

- 1 -

AS-225D

12-channel 

cascade controller

The AS-225D controller is designed for cascade control of 

12÷24 V staircase lighting, which allows to achieve the effect of 

light following a person walking up or down the stairs.

»

Control of cascading multi-point lighting system;

»

The ability to set the number of controlled light points (from 

3 to 12);

»

The ability to connect controllers in series to increase the num-

ber of controlled circuits;

»

Additional control inputs:

̶

permanent light switching (for example during houseworks);

̶

light switching lock (for example brightness sensor signal);

»

Control of light using a variety of setters including bell buttons, 

motion sensors, optical barriers, pressure sensors, etc.

»

Adjustable 

"

soft start

"

 feature – soft brightening and dimming 

of lighting;

Purpose

Features

F&F Filipowski sp. j.

Konstantynowska 79/81, 95-200 Pabianice, POLAND

phone/fax (+48 42) 215 23 83 / (+48 42) 227 09 71

www.fif.com.pl; e-mail: [email protected]

Do not dispose of this device in the trash along with other waste! 

According to the Law on Waste, electro coming from households free of charge and can 

give any amount to up to that end point of collec� on, as well as to store the occasion of 

the purchase of new equipment (in accordance with the principle of old-for-new, regard-

less of brand). Electro thrown in the trash or abandoned in nature, pose a threat to the 

environment and human health.

Summary of Contents for AS-225D















Reviews: