Locate radiants
over lugs
OFF
PILOT
HIGH
LOW
SECTION 1 - GENERAL DESCRIPTION
The chargrills, part of the Dominator Series, are
suppliedon a stand. They can also be installedupon
a counter or table using a bench mounting kit
suppliedby Falcon.
G2625, G2925, G21225, G21525 andG21825
chargrills are controlledby a combinedon/off tap
and flame failure device. Standard burner ignition is
by pilot, lit manually using a handheldgas lighter.
G2625B, G2925B, G21225B, G21525B and
G21825B chargrills are controlledby a combined
on/off tap andflame failure device. Standardburner
ignition is by pilot, lit by piezo ignition. Back-up
ignition is by gas lighter.
The control tap(s) on all models have indented
positions for HIGH (large flame) andLOW (small
flame).
Figure 1 - Radiant Positions
SECTION 2 - LIGHTING and OPERATIONS
2.1 SETTING THE RADIANTS
Before using unit each day, ensure radiants are set in
the proper positions as shown above. If radiants are
not in position shown, branding iron temperatures will
not be spreadevenly over cooking area. To reposition
a radiant, simply remove irons and adjust to ensure
radiants are positioned correctly. See Figure 1.
2.2 BRANDING IRONS
Brander bars are fitted in sets of six (600mm),
nine (900mm), twelve (1200mm), fifteen (1500mm)
andeightteen (1800mm).
Bars have integral drain channels on both sides and
are reversible. Lifting tool is suppliedto reverse bars if
required.
2.3 GRIDDLE PLATE ACCESSORY
Ensure plate is locatedin position before lighting.
The plate may require to be oiledbefore use with
some fooditems.
The unit has been testedto ensure optimum safety
and performance is achieved using just one griddle
plate. As with all equipment, optimum performance
will depend upon food type, quality and quantity with
cooking times adjusted to suit.
2.4 LIGHTING THE BURNERS
2.4.1 Manual Ignition ofPilot (All Models)
See Figures 2, 3, 4, 5, 6 and7. Proceedas follows:
a) Push tap in andturn anti-clockwise to pilot position.
b) Holdtap fully in. Insert hand-heldgas lighter in hole
relative to tap being operated. Repeat procedure
until pilot flame ignites.
c) When pilot is lit, continue to holdtap fully in for
20 seconds before release. If pilot goes out,
wait 3 minutes andrepeat from (b).
d) Repeat for remaining burners using other ports and
respective gas taps.
2.4.2 G2625, G2925, G21225, G21525,
G21825 "B" Models - Piezo Ignition
a) Push tap in andturn anti-clockwise to pilot position.
b) Holdtap fully in andpress igniter button.
c) Observe, through the slots, that pilot is lit.
d) If not, press ignition button repeatedly until pilot
does light.
e) When pilot is lit, continue to holdtap fully in for
20 seconds before release. If pilot goes out,
wait 3 minutes andrepeat from (b).
f) Repeat for remaining burners using other ports and
respective gas taps.
If piezo igniter is non-functional, then back up ignition
is achievedby manual ignition (See 2.4.1).
Figure 2 - Control Knob Details
2.4.3 Lighting ofMain Burner
a) When pilot is established, push tap in and turn
anti-clockwise to HIGH position: (large symbol) to
light burner.
b) The tap can be adjusted between HIGH and LOW
depending upon requirements.
If a burner extinguishes intentionally or otherwise,
NO ATTEMPT to re-light it shouldbe made until at
least 3 minutes have elapsed.
All manuals and user guides at all-guides.com
