A.
Hang the bowl on the bracket
and check tail
pipe alignment, then remove the bowl and
adjust the bracket as needed.
Re-hang and re-check bowl
alignment with
the drain line. Tail pipe should align with center
of drain line.
B.
Mark anchor holes
then
remove bowl without
moving hanger bracket.
A.
Find the drain nipple depth
on
the Tube Cutting Chart (left).
Measure and mark the specified
trim length
on the insert tube at
the nearest ¼” groove.
B.
Cut the tube
at the groove using a sharp
utility knife to ensure a square, flat cut.
C.
Clean burrs
from the cut end by using
emery paper.
D.
Apply lubricant
to the outside of the
rubber bushing and ribbed inside area.
E.
Insert the tube
and bushing with arrow
tab at the top. Apply lubricant to tailpipe
of housing.
USE UTILITY KNIFE TO CUT CAULK
then
use a putty knife and mallet to remove
the bowl. Remove hanger brackets,
scrape off caulk, and clean the wall.
MEASURE & MARK THE ROUGH-IN
if in-wall carrier is not used. Use a ⁵/₁₆"
masonry bit to drill hole, then install
the hanger bracket with one plastic
anchor and screw.
DETERMINE THE DRAIN NIPPLE DEPTH
by measuring the distance between the
back of the sanitary tee (or elbow) to the
front edge of the nipple.
IMPORTANT:
Use a drain machine to
remove build-up inside pipes. Clean up
to 25 feet deep then flush with water to
remove cutting debris. Never install on
copper DWV.
A.
Clean face
of existing wall flange.
B.
Install the brass flange
with the clear
inspection disc.
C.
Slowly pour water
into the drain.
D.
Use a flashlight to check the pitch/
slope
. No water should be present in
the inspection disc or nipple.
E.
Remove flange
after inspection.
ADJUST DRAIN TO ACHIEVE PITCH
only if standing water is present
(code requires ¼” drop per foot of
drain line for proper pitch). Seal wall
according to code.
PLACE THE SEAL INTO THE FLANGE
with
the ribs facing out. Install the flange
with washers and hex nuts, but do not
tighten completely.
HANG THE BOWL,
inserting
tailpipe into bushing, then
install anchor screws with
washers.
TIGHTEN FLANGE
BOLTS AND GEAR CLAMP.
POUR 5
GALLONS
OF WATER
as rapidly
as possible
into housing
to ensure
good flow
and no leaks or
standing water.
INSTALL THE GEAR CLAMP
with screw head at bottom,
but do not tighten.
DRILL HOLES
with ⁵/₁₆”
masonry bit for
the lower anchor screws and insert
plastic anchors.
The information in this document is
subject to change without notice.
©2014 Falcon Waterfree Technologies,
LLC. All rights reserved.
FalconWaterfree.com
CAULK THE BOWL
TO THE WALL
if
there is good flow
and no leaks or
standing water.
INSTALL
CARTRIDGE
per the cartridge
instruction sheet.
•
Check rough-in height to achieve 24”
rim height (17” rim height for ADA).
•
Check slope. Downhill slope, per code,
is essential because waterfree urinals
require gravity flow for drainage.
•
Check DWV material. Suitable materials
include cast iron, PVC, ABS, and
galvanized steel.
• Never install on copper DWV due to
copper’s susceptibility to corrosion
.
•
Shut off water supply and cap the nipple
with the ¾” chrome cap (provided).
•
Measure drain nipple depth (in inches)
to find trim length (in inches)
•
13
7 8
“ or more
DO NOT CUT TUBE
•
3 ¾” or less
DO NOT USE TUBE
BEFORE STARTING INSTALLATION
TUBE CUTTING CHART
FLAX
RETRO-FIT INSTALLATION
WATERFREE URINAL
866-975-0174 or 616-877-4805
CUSTOMER CARE
2" side cutter blade
Cut away wall
Lift drain line & brace
with mending plate
INCORRECT
Not centered
CORRECT
Centered
11
10
12
Install two
additional screws
CARTRIDGE
INSTRUCTIONS
1
2
3
4
Arrow
tab UP
1
2
3
4
A
C
B
D
E
CAUTION
After removing any urinal from the
drain line, it’s normal for certain naturally occurring
but
potentially hazardous sewer gases
to escape
through the opening until the waterless cartridge
is installed properly into the waterless urinal. If you
need to leave an open drain line unattended after
removing the urinal from the wall, temporarily wedge paper towels or a
rag into the drain hole to reduce any outflow of sewer gases, and remove
the paper towels or rag prior to completing the urinal or cartridge
installation.
Never smoke, have an open flame, or place your nose or
mouth near open drain lines or waterless urinal housings into which
a cartridge is not yet properly installed.
You also can wear a breathing
mask when removing or installing any waterless urinal or cartridge to
reduce potential exposure to any such gases.
OR LESS
TRIM
13 ¾"
¾
"
13 ½
½
13 ¼
¼
13
1
12 ¾
1¾
12 ½
1½
12 ¼
1¼
12
2
11 ¾
2¾
11 ½
2½
11 ¼
2¼
11
3
10 ¾
3 ¾
10 ½
3 ½
OR LESS
TRIM
10 ¼"
3 ¼
"
10
4
9 ¾
4 ¾
9 ½
4 ½
9 ¼
4 ¼
9
5
8 ¾"
5 ¾
8 ½
5 ½
8 ¼
5 ¼
8
6
7 ¾
6 ¾
7 ½
6 ½
7 ¼
6 ¼
7
7
OR LESS
TRIM
6 ¾"
7 ¾
"
6 ½
7 ½
6 ¼
7 ¼
6
8
5 ¾
8 ¾
5 ½
8 ½
5 ¼
8 ¼
5
9
4 ¾
9 ¾
4 ½
9 ½
4 ¼
9 ¼
4
10
151⁄8"
Install plastic anchor
and screw here
14
15
4
13
3
12
8
6
2
10
11
9
7
5
1
C
D
A
B
