CARRIER STUD PLACEMENT
If using
in-wall carrier, set bearing rods as
shown above.
SET DRAIN LINE HEIGHT
17” from
finished floor (standard 24” rim) or 10” for
ADA installation. Threaded nipple should
extend ½ to ¾” from wall.
A.
Clean face
of existing wall flange.
B.
Install the brass flange
with the
clear inspection disc.
C.
Slowly pour water
into the drain.
D.
Use a flashlight to check the pitch/
slope
. No water should be present in
the inspection disc or nipple.
E.
Remove flange
after inspection.
DRILL HOLES
with ⁵/₁₆"
masonry
bit for the lower anchor screws
and insert plastic anchors.
TIGHTEN COMPRESSION
NUT AND GEAR CLAMP.
DETERMINE THE DRAIN NIPPLE DEPTH
by measuring the distance between the
back of the sanitary tee (or elbow) to
the front edge of the nipple.
MEASURE & MARK THE ROUGH-IN
if
in-wall carrier is not used. Use a ⁵/₁₆"
masonry bit to drill hole, then install
the hanger bracket with one plastic
anchor and screw.
•
Check rough-in height to achieve 24”
rim height (17” rim height for ADA).
•
Check slope. Downhill slope, per code,
is essential because waterfree urinals
require gravity flow for drainage.
•
Check DWV material. Suitable materials
include cast iron, PVC, ABS, and
galvanized steel.
• Never install on copper DWV due to
copper’s susceptibility to corrosion
.
•
Measure drain nipple depth (in inches)
to find trim length (in inches)
•
13
7 8
“ or more
DO NOT CUT TUBE
•
3 ¾” or less
DO NOT USE TUBE
BEFORE STARTING INSTALLATION
TUBE CUTTING CHART
OR LESS
TRIM
13 ¾"
¼
"
13 ½
½
13 ¼
¾
13
1
12 ¾
1¼
12 ½
1½
12 ¼
1¾
12
2
11 ¾
2¼
11 ½
2½
11 ¼
2¾
11
3
10 ¾
3 ¼
10 ½
3 ½
OR LESS
TRIM
10 ¼"
3 ¾
"
10
4
9 ¾
4 ¼
9 ½
4 ½
9 ¼
4 ¾
9
5
8 ¾"
5 ¼
8 ½
5 ½
8 ¼
5 ¾
8
6
7 ¾
6 ¼
7 ½
6 ½
7 ¼
6 ¾
7
7
OR LESS
TRIM
6 ¾"
7 ¼
"
6 ½
7 ½
6 ¼
7 ¾
6
8
5 ¾
8 ¼
5 ½
8 ½
5 ¼
8 ¾
5
9
4 ¾
9 ¼
4 ½
9 ½
4 ¼
9 ¾
4
10
FLAX
NEW CONSTRUCTION
INSTALLATION
WATERFREE URINAL
866-975-0174 or 616-877-4805
CUSTOMER CARE
ADJUST DRAIN TO ACHIEVE PITCH
only if standing water is present
(code requires ¼” drop per foot of
drain line for proper pitch). Seal wall
according to code.
A.
Hang the bowl on the bracket
and check tail
pipe alignment, then remove the bowl and
adjust the bracket as needed.
Re-hang and re-check bowl
alignment with
the drain line. Tail pipe should align with center
of drain line.
B.
Mark anchor holes
then
remove bowl without
moving hanger bracket.
INCORRECT
Not centered
CORRECT
Centered
A
B
½"
to
¾"
9¾"
for ADA
installation
standard 24" rim
finished floor
16 ¾"
2¼
11⁄8
1"
151⁄8"
Drain
Cut away wall
Lift drain line & brace
with mending plate
151⁄8"
Install plastic anchor
and screw here
11
10
12
Install two
additional screws
A.
Find the drain nipple depth
on
the Tube Cutting Chart (left).
Measure and mark the specified
trim length
on the insert tube at
the nearest ¼” groove.
B.
Cut the tube
at the groove using a sharp
utility knife to ensure a square, flat cut.
C.
Clean burrs
from the cut end by using
emery paper.
D.
Apply lubricant
to the outside of the
rubber bushing and ribbed inside area.
E.
Insert the tube
and bushing with arrow
tab at the top. Apply lubricant to tailpipe
of housing.
1
2
3
4
Arrow
tab UP
1
2
3
4
A
C
B
D
E
POUR 5
GALLONS
OF WATER
as rapidly
as possible
into housing
to ensure
good flow
and no leaks or
standing water.
CAULK THE BOWL
TO THE WALL
if
there is good flow
and no leaks or
standing water.
INSTALL
CARTRIDGE
per the cartridge
instruction sheet.
CARTRIDGE
INSTRUCTIONS
HANG THE BOWL,
inserting tailpipe
into bushing, then install anchor
screws with washers.
TIGHTEN
FLANGE BOLTS.
The information in this document is
subject to change without notice.
©2014 Falcon Waterfree Technologies,
LLC. All rights reserved.
FalconWaterfree.com
CAUTION
After removing any urinal from the
drain line, it’s normal for certain naturally occurring
but
potentially hazardous sewer gases
to escape
through the opening until the waterless cartridge
is installed properly into the waterless urinal. If you
need to leave an open drain line unattended after
removing the urinal from the wall, temporarily wedge paper towels or a
rag into the drain hole to reduce any outflow of sewer gases, and remove
the paper towels or rag prior to completing the urinal or cartridge
installation.
Never smoke, have an open flame, or place your nose or
mouth near open drain lines or waterless urinal housings into which
a cartridge is not yet properly installed.
You also can wear a breathing
mask when removing or installing any waterless urinal or cartridge to
reduce potential exposure to any such gases.
PLACE THE GEAR CLAMP
and compression nut onto the
housing tailpipe.
14
15
4
13
3
12
8
6
2
10
11
7
5
1
C
D
9
