Falco Systems WMA-300 User Manual Download Page 9

 

 

 

Harmonized standards 

 
This  product  complies  with  the  following 
harmonized European standards: 
 
Safety:  EN61010-1 
EMC:   EN61326    
 

 
WEEE and RoHS 

 
Do  not  dispose  of  the  WMA-300  amplifier 
as standard waste, but bring it to a WEEE 
electronic  waste  collection  point.  The 
amplifier has been built in compliance with 
the RoHS directive. 

 
 
Warranty 

 
Falco  Systems  products  are  guaranteed 
against  malfunction  due  to  defects  in 
materials or workmanship for a period of 1 
year from the date of shipment.  
If  a  malfunction  occurs  during  this  period, 
the  product  will  be  repaired  or  replaced 
without  charge.  The  product  will  be 
returned to the customer prepaid. 
 
The warranty does not apply to: 
- Exterior finish or appearance 
-  Malfunction  resulting  from  use  or  ope-
ration  of  the  product  in  other  ways  than 
specified in the user manual 
- Malfunctioning due to misuse or abuse of 
the product 
- Malfunctioning occurring after changes or 
repairs  have  been  made  by  anyone  other 
than Falco Systems. 
 
To  obtain  warranty  service,  the  customer 
has  to  inform  Falco  Systems  first  via 
[email protected] to receive further 
instructions.  
 

Falco  Systems  will  not  be  liable  for  any 
consequential damages, including, without  
limitation, devices or equipment connected 
to the product, injury to persons or property 
or  loss  of  use.  See  for  more  details  the 
Falco  Systems  Standard  Terms  and 
Conditions  of  Sale,  which  can  also  be 
obtained via [email protected].  
 
 

User manual version 

 
User manual version: 2.4 
Date: July 2019 
 
 

Falco Systems 

 
Falco Systems 
Remisestraat 1   
2225 TH Katwijk aan Zee 
Tel. +31 (0)6 21840996 
Fax. +31 (0)20 2031 445 

 

Email: [email protected] 
http://www.falco-systems.com 

Summary of Contents for WMA-300










Reviews: