Familiarize yourself with these rules and the
application, limitations and potential hazards
of using the jack.
•
DO NOT
use a trolley jack for any other application
other that lifting.
•
DO NOT
exceed the maximum lifting capacity as
stated on the product or it the operating manual.
• DO NOT
allow the vehicle to move during a
jacking operation, or use the jack to move a vehicle.
•
DO NOT
operate the jack if any parts are
damaged or worn prior to use.
•
DO NOT
top up the hydraulic system with brake fluid.
Use hydraulic jack oil only with a rating of SAE 10.
•
DO NOT
use a ‘cheater’ pipe, lever, or other device to
extend the handle length for additional leverage.
•
DO NOT
adjust the safety overload valve. This is
correctly set at the factory and no further readjustment
is necessary.
• DO NOT
use a jack to support a lifted load.
Appropriate rated axle stands should be correctly
positioned and the load lowered as soon as possible,
to provide a safe working environment.
• DO NOT
work under the vehicle until axle stands
have been correctly positioned under the vehicle.
• DO NOT
lift the vehicle if there is a likelihood of
spillage of fuel, battery acid, oil or other dangerous
fluids.
• DO NOT
allow an untrained or young person to
operate the jack without full supervision.
•
ALWAYS
inspect the jack before use.
•
ALWAYS
use the jack on level solid ground,
concrete is preferable. Avoid tarmac surfaces as
these are prone to sinking.
•
ALWAYS
ensure the engine is switched off and that
there are no passengers in the vehicle.
•
ALWAYS
ensure the vehicle handbrake is engaged
and transmission is in gear or “PARK” if the vehicle
has an automatic gear box.
• ALWAYS
chock the wheels of the vehicle to be
jacked at the non-lifting end.
•
ALWAYS
place the jack under the lifting point
recommended by vehicle manufacturer, check the
vehicle handbook if in doubt. Check that the lifting point
is sound and centred on the jack saddle prior to lifting.
•
ALWAYS
ensure a minimum distance of 0.5m
between the vehicle and any static objects such as
walls, doors or other vehicles to allow for the vehicle
tilting during lifting.
•
ALWAYS
Ensure the jack wheels are free to move
and that there are no obstructions.
•
ALWAYS
store the jack in is retracted position in a
safe, dry place.
Operation Instructions
SPECIFICATIONS
FAI AUCJACTRO3
Features a 100mm high saddle extension
for use on vehicles with a high ground
clearance. To extend the saddle height
remove the black saddle
(1)
and insert the
saddle extension part
(5)
into the saddle
assembly, then slot the saddle back into the
extension. Ensure that the saddle and the
extension are fully seated before using the jack.
Open release valve
anti-clockwise
Close release valve
clockwise
Fig.2
1. Saddle
2. Release Valve
3. Pump Sleeve
4. Quick Lift Sleeve
(FAI AUJACTRO3 ONLY)
5. Saddle Extension
(FAI AUJACTRO3 ONLY)
Fig.1
1
2
3
4
5
3
1. BEFORE USING JACK:
Open the release
valve
(2)
by turning counterclockwise just
enough to open valve, do not fully remove
the valve from the base (See
Fig.2
)
Insert the handle into the pump sleeve
(4)
and pump about 6 full strokes to ensure
complete distribution of the hydraulic oil.
2. TO RAISE:
Close release valve by turning
clockwise. Check to see that the saddle
(1)
is centered on the lifting point and then
pump the jack.
3.
The
FAI AUCJACTRO3
jack features a
Quick Lift function, one movement of the
lever will lift the saddle to its full working
height. This allows the saddle to be quickly
brought into contact with the vehicle saving
unnecessary pumping. With the release
valve closed insert the jack handle in to the
Quick Lift Sleeve
(4)
and push down. Once
the saddle has made contact with the vehicle
insert the handle into the pump sleeve and
operate as normal to raise the vehicle.
4. TO LOWER:
Slowly open release valve
(2)
counterclockwise just enough to open the
valve, do not fully remove the valve from
the base
2
Specifications
Lifting capacity: 1500kg
Minimum height: 128mm
Maximum height: 300mm
FAI AUJACTRO15
FAI AUJACTRO3
Lifting capacity: 2500kg
Minimum height: 150mm
Maximum height: 430mm
Minimum extended height: 250mm
Maximum extended height: 530mm
Part Identifier
