Fairport PP46 Operation, Spare Parts And Service Manual Download Page 7

  Position the engine speed control lever to give required speed (usually full speed). 
Commence compaction.  The compactor is self-travelling.  Its speed of travel and the 
number of passes required to achieve optimum compaction depends on the type and 
condition of material being compacted and the layer depth. 
Uniformly graded granular material compacts far more efficiently than wet cohesive 
material. 
When Compacting block paving always use a rubber attachment mat, contact your 
agent for details. 
When compacting blacktop always use a water spray, contact your agent for details. 
 
Do not run the machine on solid surfaces, as this is likely to cause damage. 
 

 

7. LUBRICATION 

 

The vibrator pack is a ‘lubricated for life’ unit.  It will only need relubricating if there is 
a need to replace the seal and/or bearings.  Replenish the housing with 150ml of 
engine oil Grade 10W/30 or 15W/40. 
 

 
8. VEE BELT ADJUSTMENT 

 
It is important to note that belt tension in this application is much less than is 
generally accepted as normal.  Too high a belt tension may lead to engine damage, 
excessive vibration in the handle, short belt life and short vibrator shaft bearing life 
due to excessive transmission of vibration through the belt. Correct adjustment is 
achieved by moving the engine back to take the slack out of the belt. With light finger 
pressure on top of the belt and at the centre of the span, a deflection of between 
5mm and 10mm is expected. 
 

 

9. WARRANTY CONDITIONS AND CLAIMS PROCEDURE 

 
All products supplied by Fairport Construction Equipment Ltd (hereafter referred to as 
FCE) are warranted to be free of defects due to faulty materials or workmanship for a 
period of 12 months from the date of original despatch from FCE or 3 months for all 
spare parts used in repairs carried out by FCE or an authorised dealer or repairer. 
 
If the goods have been purchased through a stockist the above warranty periods also 
apply from receipt of the goods by the user of the equipment up to a total of a further 
6 months from date of despatch from FCE whichever is earlier. 
Filter elements, gauges and oils are specifically excluded from this warranty. 
FCE shall at their option repair or replace, during normal working hours, goods 
accepted as faulty free of charge to the user.  
For proprietary items such as engines, the original manufacturer’s warranty and 
conditions shall apply. 

CONDITIONS 

The goods shall be returned at the purchaser’s expense to FCE or to a destination 
FCE may reasonably direct.  Carriage costs will be refunded if warranty is accepted. 
Warranty claims will not be considered where there is evidence that failure has been 
caused by carelessness, improper use, negligence, inadequate servicing, incorrect 

Summary of Contents for PP46
















Reviews: