background image

www.Fagorcommercial.com

 

 

PAGE 13 

 

REACH-INS OPERATIONAL SERVICE MANUAL / Rev.JUN. 2015

 

2.

 

Press the up and down arrows to increase or decrease the set temperature. Then press 
the set button to save the new set point. 

 
 
 
 

Note: 
The maximum value you can set in the controller is: For refrigerators: 5°C (40°F) 
For freezers: -16°C (2°F) 

 

3.

 

If you wish decrease the value of the set point for a new temperature, press the button 
DOWN  arrow  (see  the  picture  below).  Press  this  button  to  reach  the  desired  value. 
Release the button and then press the SET button to keep, and save, the new value. 

 

 

Note: 
The minimum value you can set in the controller is: For refrigerators: -1°C (30°F) 
For freezers: -23°C (-8°F) 

 

Changing the reading temperature from °F to °C 

 

To change the reading of the temperature from °F to °C or vice versa, you need access to the 
programming  mode  in  the  controller.  To  do  this,  press  and  hold  the  SET  button  for  five  (5) 
seconds until “PS” is shown in the display. Release the button and press the SET button one 
time. Now you will see the number zero (0). With the button UP arrow, set a value of “22” and 
then press the SET button. You will see the “PS” again. Use the button DOWN arrow to find 
the parameter “EZY” and press the SET button one time. Using the UP or DOWN button set a 
value according to the chart below. 
 

 
 

 

 
 

 
 
 
 
 
 
 
 
Note: 

For Refrigerators

 

EZY Value

 

Application

 

Temperature in °F 

Refrigeration 

Temperature in °C 

Refrigeration 

 

For Freezers

 

EZY Value

 

Application

 

Temperature in °F 

Freezer 

Temperature in °C 

Freezer 

Temperature in °F 

Refrigeration 

Temperature in °C 

Refrigeration 

 

Summary of Contents for QF-1





























Reviews: