Programming:
1) Set
DIP-sw. 5
to
ON.
The red led 1 on the PCB flashes.
2) Press the number of
minutes
corresponding to the activation delay
as
required (max.1439 minutes).
3) Press output
A
or
B
through which the required function is activated.
4) Set
all the DIP-switches
to
OFF
Confirmation of the operation: long beep and green led alight for 2 sec.
Using the function:
Press the
access code
followed by
A
or
B
as programmed. The green led
goes on for 1 sec. followed by an activation beep.
The blue led starts flashing and indicates that the function has been activated.
ON
1)
5
2)
3)
OFF
4)
5
OUTPUT DELAY
The pulse is delayed (for a number
of minutes) after pressing the
access code.
In order to
RESET
(the function is cancelled) press the following sequence:
A
or
B - access code - A
or
B
The green led goes on for 1 sec. followed by a confirmation beep, while
the blue led stays illuminated.
1
2 3
4
5 6
7
8 9
A
B
Diagram
Each pulse by the access code
energizes or de-energizes the
output relay.
Each pulse by the access code
delays (for a number of minutes)
the energizing of the timed relay.
pulse
output
TIMED WITH 2 PULSES
A pulse is given after the access code
has been pressed and another one
is given after a set time (minutes)
ON
1)
6
2)
3)
OFF
4)
6
BISTABLE
Connect the
main PCB
to the
control box
(Pic. 8) or to the external control relay,
then store an access code with required outputs
.
Different functions can be achieved by one or both of the outputs, but different access codes to one relay carry out the same function.
NOTE WELL: functions are reset in case of a power failure, even if instantaneous
.
ON
1)
7
2)
3)
OFF
4)
7
TIMED DELAY
WITH 2 PULSES
1)
ON
8
2)
3)
OFF
8
4)
5)
The relay is energized and remain
energized for the time as set
(in minutes).
ON
1)
9
2)
3)
OFF
4)
9
6)
Steps to cancel the additional functions from the single relay and set the
DGT 61 unit back to normal functioning.
1)
ON
5
2)
OFF
5
3)
Programming:
1) Set
DIP-sw. 6
to
ON.
The red led 1 on the PCB flashes.
2) Press the number of
minutes for the
time required after the first pulse
(max. 1439 minutes).
3) Press either
A
or
B
output by which the function is to be activated.
4) Set
all the DIP-switches
to
OFF
.
Confirmation of the operation: long beep and green led alight for 2 sec.
Using the function:
Press the
access code
followed by
A
or
B
as programmed. The green led
goes on for 1 sec. followed by an activation beep.
The blue led starts flashing and indicates that the function has been activated.
1
2 3
4
5 6
7
8 9
A
B
Diagram
In order to
RESET
(the function is cancelled) press the following sequence:
A
or
B - access code - A
or
B
The green led goes on for 1 sec. followed by a confirmation beep, while
the blue led stays illuminated.
Diagram
7
A
B
Programming:
1) Set
DIP-sw. 7
to
ON.
The red led 1 on the PCB flashes.
2) Press only the
button key No. 7
.
3) Press either
A
or
B
output by which the required function is to be actived.
4) Set
all the DIP-switches
to
OFF
Confirmation of the operation: long beep and green led alight for 2 sec.
Using the function:
Press the
access code
followed by
A
or
B
as programmed. The green led
goes on for 1 sec. followed by an activation beeping.
Programming:
1) Set
DIP-sw. 8
to
ON.
The red led 1 flashes.
2) Press the number of
minutes for the delay with time 1
(max 1439 minutes)
3) Press either
A
or
B
output by which the required function is to be activated.
4) Press the numer of
minutes for
time 2
(max. 1439 minutes).
5) Press ether
A
or
B
as set in step 3).
6) Set
all the DIP-switches
to
OFF
.
Confirmation of the operation: long beep and green led alight for 2 sec.
Using the function:
Press the
access code
followed by
A
or
B
as programmed. The green led
goes on for 1 sec. followed by an activation beep.
The blue led starts flashing and indicates that the function has been activated.
Diagram
A
B
A
B
In order to
RESET
(the function is cancelled) press the following sequence:
A
or
B - access code - A
or
B
The green led goes on for 1 sec. followed by a confirmation beep, while
the blue led stays illuminated.
Programming:
1) Set
DIP-sw. 9
to
ON.
The red led 1 on the PCB flashes.
2) Press the number of
minutes corresponding to the activation time
as
required (max. 1439 minutes).
3) Press output A or B as required for the function to be activated.
4) Set
all the DIP-switches
to
OFF
.
Confirmation of the operation: long beep and green led alight for 2 sec.
Using the function:
Press the
access code
followed by
A
or
B
as programmed. The green led
goes on for 1 sec. followed by an activation beep.
The blue led starts flashing and indicates that the function has been activated.
1
2 3
4
5 6
7
8 9
or
A
B
In order to
RESET
(the function is cancelled) press the following sequence:
A
or
B - access code - A
or
B
The green led goes on for 1 sec. followed by a confirmation beep, while
the blue led stays illuminated.
Diagram
Diagram
A
B
1
2 3
4
5 6
7
8 9
REMOVING THE ADDITIONAL FUNCTIONS
1) Set
DIP-sw. 5
to
ON.
The red led 1 on the PCB flashes.
2)
Press A (or B) - access code - press A (or B)
.
3) Set
all the DIP-switches
to
OFF
.
Confirmation of the operation: long beep and green led alight for 2 sec.
A
B
Power supply 2x0.5mm²
Connections to the keypad
Keypad absorption
Stand-by relay absorption
Energized relay absorption
Working temperature
N.O. channels
N.C. channels
Communication distance
Output contacts
kaypad protection standards
PCB protection standards
12-24Vdc/ac
4 x 0.5mm²
15 mA
4 mA
27 mA
-20° +80°C
2
1
max 100 m
1A-125V-60VA
IP 54
IP 53
meccanica
FADINI
ADDITIONAL FUNCTIONS:
can be achieved by the A and B outputs through one or more access codes
Instructions manual DGT 61 digital keypad
GB
meccanica
FADINI
Instructions manual DGT 61 digital keypad
GB
ADDITIONAL FUNCTIONS:
can be achieved by the A and B outputs through one or more access codes
TIMED BISTABLE
OVERALL DIMENSIONS
TECHNICAL DATA
The manufacturer reserves the right to change this manual
without prior notice, and is not liable for incorrect applications
or damages to persons and properties.
Pic.9
page 11
page 12
main PCB
time in minutes
(max 1439 = 24h)
ALL DIP-SW.
TO OFF
main PCB
or
output
Time 1
pulse
output
Time 2
Time
pulse
output
main PCB
time in minutes
(max 1439 = 24h)
ALL DIP-SW.
TO OFF
main PCB
or
output
main PCB
press key 7
ALL DIP-SW.
TO OFF
main PCB
or
output
Time
pulse
output
main PCB
time 1 in
minutes
(max 1439)
ALL DIP-SW.
TO OFF
keypad
time 2 in
minutes
(max 1439)
keypad
keypad
or
or
Time
pulse
output
main PCB
time in minutes
(max 1439 = 24h)
ALL DIP-SW.
TO OFF
main PCB
output
ALL DIP-SW.
TO OFF
LONG BEEP
gree led
for 2 seconds
or
main
PCB
output
access
code
or
output
main
PCB
Manufacturing company:
The model:
DECLARES UNDER ITS OWN RESPONSIBILITY THAT:
DECLARATION OF CONFORMITY
of the manufacturer
DGT 61 is a digital keypad designed to be sold and installed into a comprehensive "Automatic System",
including the original accessories and components as recommended by the Manufacturing Company.
The installer must issue the Installer's Declaration of Conformity and carry out all the tests required to
comply with the existing regulations.
The manufacturing company is not liable for any incorrect use of its product.
The product conforms with the following norms as specified below:
- Low Voltage Directive
2006/95 CE
- Electro-magnetic Compatibility Directive
2004/108/CE
and
92/31 CEE
GB
DGT 61
made in Italy
the gate opener
Date:
20 - 04- 11
meccanica
FADINI
Meccanica Fadini s.n.c.
Direttore Responsabile
The responsible manager
Via Mantova 177/A - C.P. 126 - 37053 Cerea (VR) Italy
Tel. +39 0442 330422 - Fax +39 0442 331054
e-mail: [email protected] - www.fadini.net
DGT 61
12-24V
cc/ca
A
B
NC
X
Y
Z
91
73
27
Main
PCB
Surface mount
keypad
40
72
74
1
2
3
4
5
6
7
8
9
A
B
STOP
FADINI
Keypad
29
25
54
Ø56
Recess mount keypad