Factory Five Racing '33 Hot Rod Assembly Manual Download Page 351 | Manualshive

Page: 351 / 710

background image

350

www.factoryfive.com

508-291-3443

2015 IRS

Once the car has been aligned, use a 1

5

/

8

” wrench to loosen the upper control arm large jam nut and put

some Loctite on the threads where the jam nut will sit.

Retighten the jam nut.

Fluid Levels and Grease



Grease gun, chassis grease, ratchet, rags



Transmission fluid, rear axle gear oil, engine oil, coolant, water

Transmission

Fill the transmission with fluid and install the shifter assembly. Leave the shift handle and knob off for
now.

Engine

Fill the engine with Oil and coolant. Both these fluids should be rechecked after you have started the
engine for the first time. Make sure there is some coolant in the overflow to start out, about ⅓ full is
good.

Suspension

All of the suspension and steering components that have grease fitting need to be greased. With a grease
gun squeeze grease into each fitting on all the control arms, including rear lowers on a slid axle, and tie
rods.

«
...
349
350
351
352
353
...
»

Summary of Contents for '33 Hot Rod







































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for '33 Hot Rod

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Kargo Master Pages: 5

Brand: Whispbar Pages: 15

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: REVCAMUK Pages: 4

Brand: CITROËN Pages: 301

Brand: Alfa Romeo Pages: 8

Brand: BURY Pages: 2

Brand: Mercedes-Benz Pages: 358

Brand: PAC Pages: 14

Brand: Kolpin Pages: 3

Brand: Mercedes-Benz Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands