background image

PILOT-OP-EN 

- 23 -

BATTERY CHARGING

Charger Specifi cations

• 

Output voltage of 36 Volts

• 

Output current of 25 amps max 

(Optional)

• 

Input voltage of 110 Volts/ 60 Hz 

(220V/50 Hz available)

• 

Automatic shut off circuit

• 

Made for Deep Cycle Batteries 

DANGER

Explosive hydrogen gas forms when Batteries are 
charging. An open fl ame or spark can cause this gas 
to explode. Serious personal injury or property damage 
could occur. Only charge the Batteries in this machine 
in a well ventilated area.

WARNING

Before you service a Battery, always wear face protec-
tion, protective gloves and protective clothing.  Battery 
acid or battery explosion can cause serious injuries.

WARNING

The Batteries in this machine contain sulfuric acid, 
which causes burns to skin. If battery acid contacts 
clothing or skin, rinse the effected area with cold water 
immediately. If battery acid gets on your face or in your 
eyes, fl ush the area immediately with cold water and 
seek medical attention.

CAUTION

Always use the automatic battery charger provided by 
the manufacturer of this machine to charge the Batter-
ies of this machine. It is designed to charge the Batter-
ies at the appropriate rate. If you must use a different 
charger, disconnect the Batteries before charging to 
avoid damage to the electronic speed controller.

EXTERNAL BATTERY CHARGING:

1. 

Transport machine to a well ventilated area for charging.

2. 

Turn the machine 

OFF 

(   ).  Remove key.  Tip Seat 

(A)

 to 

side for Battery Access 

(SEE BELOW)

.

3. 

Check the water in each Battery 

(B) 

(SEE BELOW)

.  Do 

not charge the machine unless the water is slightly higher 

than the plates.  If needed, add enough distilled water to just 
slightly cover the plates.  Be careful not to over fi ll.  Batteries 
can overfl ow during charging.  Replace caps before charging.

4. 

First, plug the (grey 50) Charger plug into the machine’s 
Charger Port 

(C) 

(SEE BELOW)

.  After the Charger plug is 

connected, plug the charger power cord into a grounded 110 
Volt / 60 hz standard wall outlet 

(D) 

(SEE BELOW)

.  Ensure 

to leave the seat lid open while charging.

5. 

The Charger will begin charging and shut off when fully 
charged 

(check Charger Amp gauge)

.

6. 

After the Charger has turned off - First, unplug the Charger 
from the wall outlet.  Second, unplug the grey 50 Charger 
plug from the machine.

7. 

Recheck the cell level after charging.  If needed, add distilled 
water up to the correct level.  Be certain to replace the caps 
securely and to wipe off the top of the Batteries with a clean 
cloth. 

WATER LEVEL SHOULD BE 
1/8'' ABOVE PLATES

B

C

C

D

A

Summary of Contents for Pilot 28'' DISK










































Reviews: