21
eNGLIsh
OPERATION
WARNING:
Always observe the safety instructions and
applicable regulations.
NOTICE:
Do not drop the Brake Disc and Tyre Analyzer.
3. Configure the Bluetooth® connection. Refer to
COM Port
Configuration
under
home screen
.
4. Enter workshop information. This information will be put
on all reports generated by this tool. Refer to
Workshop
Configuration
under
home screen
.
5. Verify the Brake Disc and Tyre Analyzer firmware is up to
date. Refer to
Firmware Update
under
home screen
.
Brake Disc and Tyre Analyzer Automatic
Activation
The first activation of the Brake Disc and Tyre Analyzer is
performed automatically by the SCANDIAG software
1. Before proceeding be sure to have set the correct COM port.
Refer to
COM Port Configuration
under
setuP MeNu
for
further details.
2. Click on one of the functions menu on the Home screen of
SCANDIAG software Complete all steps in
Brake Disc and
Tyre Analyzer and Workshop Configuration.
Refer to
Home Screen
under
scANDIAG setup
for further details
about the Home Screen or the functions.
3. Follow the directions on the screen.
Brake Disc and Tyre Analyzer Manual Activation
Manual activation of the Brake Disc and Tyre Analyzer is possible
only if automatic activation fails.
1. Contact you retailer and ask for activation code.
2. On the display unit/computer, wait for the manual activation
code field to unlock.
3. Enter the activation code and press the GO button.
4. Press the EXIT button to end the procedure.
Brake Disc and Tyre Analyzer Test and Calibration
NOTICE:
Brake Disc and Tyre Analyzer must be calibrated
before using the tool. Refer to
Periodical tool check
under
setup Menu
for further instruction.
1. Test the Brake Disc and Tyre Analyzer.
ACTIVATION
Brake Disc and Tyre Analyzer and Workshop
Configuration
1. Charge the Brake Disc and Tyre Analyzer battery. Refer to
Charging Brake Disc and Tyre Analyzer Battery
under
Brake Disc and tyre Analyzer setup.
2. Check the display unit/computer to make sure bluetooth
is enabled.
-
to activate a Brake Disc and tyre Analyzer,
drag the
slider to the right.
-
to deactivate a Brake Disc and tyre Analyzer,
drag
the slider to the left.
1. Click Save
.
Number of Acquisitions
1. Click Settings
.
2. Select the desired value between 1 and 5 in the menus
Number of acquisitions for brake disc testing
and
Number of acquisitions for tire testing
.
3. Click Save
.
4. The calculated result is the arithmetic mean of the values
aquired at the end of the measurements of brake disc or tyre
checks. SCANDIAG software indicates each acquisition in the
graph with a different color.
Workshop Configuration
1. Click Workshop Data
.
2. Enter the required information in the specific fields.
3. Click Save
.
Periodical Tool Checks (Fig. C)
1. Switch the Brake Disc and Tyre Analyzer on. Refer to
Multifunction Button
for further direction.
2. Place the magnet
5
into the measurement system check
adapter
7
as shown in Figure C.
3. Click Periodical Checks
and follow the instructions that
appear on the screen.
Firmware Update
1. Click Firmware update
.
2. Follow the instructions that appear on the screen.
Test Archive
1. To access a report saved in SCANDIAG software click Test
Archive
.
NOte:
Saved reports can be organized by liscence plate,
date, or time by clicking on the word PLATE, DATE, or TIME.
2. To open a report from the list,
-
double click the report
-
single click and click the Print icon
.
3. To print the report as a PDF, select Print Preview
then
print to PDF.
4. To export the report, click Export
. A prompt will open,
allowing the user to choose a location for the file to print.
Brake Disc Wear Analysis (Fig. A, E)
WARNING:
Do not activate the laser before correctly
positioning the Brake Disc and Tyre Analyzer for
the measurement.
To achieve optimal results, position the Brake Disc and Tyre
Analyzer as shown in Figure E.
RecOMMeNDAtION:
Take more than one measurement if the
disc is severely corroded.
RecOMMeNDAtION:
Ensure the vehicle brake system is
functioning per the manufacturer's specification.
Preparation
1. Disconnect the tyre wear analysis adapter
6
or the
measurement system check adapter
7
. Refer to
Adapter
for
further instruction.
Summary of Contents for Scandiag DX.TSCANPB
