User manual MatriX I.T.C. Honeywell
7 <
<
<
<
Pairing remote control with I.T.C.
Press the "connect" button of the I.T.C., which is
located behind the small service door, until it
flashes blue. (See fig. 1.5).
The LED continues to flash blue for as long as the
pairing mode is activated (60 sec.).
On the remote control simultaneously press
buttons 1 and 5 until the LED rapidly starts flashing
blue and release the buttons. (See fig. 1.3).
Now the pairing process will start automatically. If
pairing is successful, both on the remote control
and I.T.C. the LED will briefly flash green.
If pairing fails, on the I.T.C. and/or the remote
control the LED will flash red momentarily. If this
occurs, please repeat the procedure again and
check whether all activities have been carried out
correctly and reduce the distance between the
remote control and the I.T.C.. After the end of the
pairing procedure the blue flashing of the LED will
stop.
You may also follow the instruction using the App.
Click on the main menu in the upper left corner
and choose "Info" and then "Connect remote
control".
LED signals in "power" symbol remote
control (see fig. 1.1)
LED flashes white:
o
Fire starting procedure is running.
LED flashes orange (1 time):
o
Min or max reached.
(Flame height, light intensity, etc.)
o
Start interrupted or not successful
(During waiting period no start
possible. When using App remaining
waiting period is displayed).
o
Switching on too quickly after
switching off.
LED flashes blue (heart rate rhythm with
intervals of 0.5 sec.):
o
I.T.C. in connect mode (60 sec.) for
pairing Smartphone/Tablet.
LED flashes blue (continuously):
o
Remote control in pairing mode for
pairing with I.T.C..
LED flashes green (1 up to 4 times):
o
Transmitting user command.
(Remote Control repeats command
max 4 times if the command is not
confirmed by the I.T.C.).
LED flashes orange (4 times):
o
1 or more active I.T.C. warnings. (To
be read in the App).
LED flashes red (7 times):
o
1 or more active I.T.C. failures.
(To be read in the App).
Replacement remote control batteries
Replacement of the batteries in the remote control
is indicated by the App in a timely manner. You will
be notified of this on your Smartphone or Tablet.
Please note!
After replacing the batteries, it is not
necessary to pair the remote control with the
I.T.C. again!
Remove the battery cover on the back of
the remote control. (See fig. 1.6).
Place 2 AA 1.5 Volt Alkaline long live
batteries.
Place the battery cover again.
Control via Smartphone or Tablet
Suitable for Android or iOS operating systems in
combination with the free download "Faber ITC
V2" App
Download and install the App on your device.
Faber App uses a Bluetooth connection with the
fire that needs your Smartphone or Tablet
Bluetooth to be enabled.
Your Smartphone/Tablet needs to be paired with
the I.T.C.. Follow the instructions in the App or
consult section 5.1. You can connect an unlimited
number of devices.
Pairing Smartphone/Tablet with I.T.C.
(via remote control)
On the remote control, press the OFF button (top
left) and hold it until the blue LED starts flashing
(heart rate rhythm) and release the button.
(See fig. 1.2).
The LED continues to flash blue for as long as the
pairing mode is activated (60 sec.).
Start the App on your Smartphone or Tablet.
If the control screen is shown:
Press the "list" symbol next to the name
of the fire in the control screen.
If you wish to add an extra fire:
Press the "+" button at the bottom of the
screen.
Connection is automatically realised now.
When an exclamation mark appears on the screen,
this is important information for your settings of
your Smartphone or Tablet, see fig. 2.9.
