1). Place suitable cooking utensils in the center of the top plate and plug in, then pressing
, the light
of Heating will shine, and the cooker will heat the cookware at 1400W. The power rate can be adjusted
by "
+
” or “
-
”. Please be noticed that the power range is from 500~2000W.
2). Pressing Function Selection button, Heating. Temp and Timer can be transformed circularly. The
default temperature of setting temperature in is 60
℃
and the default timer is 0 minutes. This
induction cooker is equipped with memory function. The power level, temperature level and timer
level interval will be stored even you change from POWER to TEMP and then back to POWER.
3). Press the "
+
” or “
-
”, the Heating can be adjusted from 500~2000W, the Temp can be adjusted from
60
℃
to 240
℃
, and the Timer can be adjusted from 0 minute to 180 minute. Be noticed that if you want
to cancel Timer, you just need to adjust to 0 during the Timer state. And if there is no operation in two
hours, the unit will be off automatically.
4). The appliance is equipped with an overheat protection. If the pot or pan is getting too hot, the
appliance will switch off power, a buzzer sounds and on the display occurs
”E2”. Should this happen,
wait for some minutes and cool the appliance down. After that, the appliance works without problems.
If meat or vegetables should the roasted, please use the temperature function to avoid any over
heating .
5). When take away the cooking pot during the working state, the induction cooker will make a sound
“bi”,
then the unit will be off 1 minute later automatically.
6). Lock, press the Lock button for two seconds,it could lock the function you want, The induction cooker
has no response when press any other button during this state(except ON/OFF
), If you want to
select other function, press the Lock button for 3 seconds, every button will be work normally.
Ⅳ
.Usable and Non-usable Utensils
1). Usable Pans
Steel or cast iron, enameled iron, stainless steel, flat-bottom pans / pots with diameter from 12 to 26cm.
Enameled Iron Iron or Enameled Castiron Pan Iron Pot Deep-Fry Pan Stainless Steel Pot Iron Plate
Pot Iron Pot
2). Non-usable Pans
Heat-resistant glass, ceramic container, copper, aluminum pans/pots. Rounded-bottom pans/pots with
bottom measuring less than 12cm.
Rounded Bottom Aluminum Bottom Measuring Pot with Stands Ceramic Pot Heat-Resistant
Pot Copper Pot Less than 12cm Glass Pot
Ⅴ
.How to Clean
1). Disconnect plug and wait until the unit is cooled down completely. Clean after using every time.
2). If the pots/pans are used without being cleaned, discoloration or cooked on stains may be caused.
3). Do not use benzine, thinner, scrubbing brush or polishing powder to clean the induction cooker.
4). Wipe using dish washing agent and damp cloth.
5). Use vacuum cleaner to suck up dirt from the air intake and exhaust vent.
6). Never run water over the unit (Water gets inside may cause malfunction).
Ⅵ
.TROUBLESHOOTING
Error Message
Cause
Solution
E0
No pan or unsuitable pan
Use pan or suitable pan
E1
Temperature of IGBT is too
high or the fan inside is not
working,or sencor organ is
failure.
．
First Cleaking ventilation
slots if blocked.If no then let
the device cool off for a few
minutes,then try to operate
the device again .
．
Contact supplier to repair
E2
Sensor is failure or the
temperature of the pan is too
high(when the pan is dry or
the
unsuitable
pan,
the
temperatue will be very high
，
the induction will cut the
power to protect the IC chip)
．
Remove the cookware form
the hob. Let the device cool
off for a few minutes,then try
to operate the device again.
E3
voltage is unusual.
.Pls
check
the
voltage
first,then try to operate the
device again.
