Faber EGYZIA Installation Instructions Manual Download Page 7

WARRANTY  &  SERVICE

This rangehood carries a limited warranty against manufac-

turer's defects.  To obtain warranty service, contact the dealer 

from whom you purchased the rangehood, or the local Faber 

distributor.  If you cannot identify a local Faber distributor, 

contact  Faber  USA  at  (508)  358-5353  for  the  name  of  a 

distributor in your area.

STANDARD  INTERNAL  BLOWER

WIRING  DIAGRAMS

*AVAILABLE  REMOTE  BLOWER

This  rangehood  uses  Flourescent  Lamp  Type  F33-15W-T8  and 

Starter Type S2.

USE  AND  CARE  INFORMATION

This rangehood system is designed to remove smoke, cooking 

vapors and odors from the cooktop area.

Rangehood Control Panel

The control panel, located on the right-hand side under the 

canopy, is designed to disappear from view when not needed.  

To open, press upward on the front edge and release.  The 

panel will drop into sight.  To close, push upward on the bot-

tom left corner of the control panel and it will slide up into 

the hood.  The position and function of each control button 

is indicated in FIGURE 15.

FIGURE  15

Light On/Off Button ( L )

On/Off switch for the fluorescent light.    Move the switch to 

"1" to turn the light ON and to "0" to turn it OFF.

Blower On/Off Button  ( M )

On/Off switch for the blower.    Move the switch to "1" to turn 

the blower ON and to "0" to turn it OFF.

Blower Speed Button ( V )

Variable speed control for blower.  Move the switch to the far 

left for LOW Speed and to the far right for HIGH speed.  

For Best Results

Start  the  rangehood  before  cooking  and  allow  the  unit  to 

operate for several minutes after cooking is complete to clear 

all smoke and odors from the kitchen.

Cleaning

The metal grease filters should be cleaned frequently in hot 

detergent solution or washed in the dishwasher.   Stainless steel 

cleaner should be used on stainless rangehoods.  Abrasives 

and scouring agents can scratch stainless steel finishes and 

should not be used to clean finished surfaces.

Replacing the Fluorescent Light

To  replace  the  fluorescent  light,  remove  the  diffuser  clips 

(T) from both ends of the glass diffuser.  Carefully slide the 

glass diffuser all the way to the right.  Lower the left end of 

the glass below the support flange (Z), then remove the glass 

by sliding it back to the left.  Replace the diffuser glass by 

reversing these directions.

FIGURE  16

Version11/00 - Page 7

* If a remote blower is used with this rangehood, current draw must 

not exceed 4 amps.

L

M

V

Summary of Contents for EGYZIA













Reviews: