1 7
1 8
E124 28
532365 - Rev.A
P2
SLH/SLH LR
P1
SLH/SLH LR
- +
-
RADIO
CLOCK BATTERY
BATTERY
RESET
SETUP
R2
R1
PRGRM
LCD1
POWER
SUPPLY
USB
F
XF MODULE
+
8.8.
1 2
1 2 1 2
3 4 5 6 7 8
11 12 13 14 15 16 17 18 19 20
DL1 DL2 DL3 DL4
DL9 DL10 DL11
DL12
SW3
DL14
BATTERY
SW1
SW2
DL13
DL5
DL6 DL7 DL8
ALARM
RESET
DL12
DL1 DL2 DL3DL4
DL6
DL7DL8
DL9
DL5
DL13
DL10 DL11
2EASY
OUT2
OUT1
LAMP LOCK MOT1 MOT2
+
-
+
-
IN1
IN2
IN4
IN5
GND
IN3
GND
+24
FCA
1
FCC
1
FCC
2
FCA
2
GND
GND
GND
ENC
1
+24
ENC
2
LED
R1
- +
-
RADIO
CLOCK BATTERY
BATTERY
RESET
SETUP
R2
R1
PRGRM
LCD1
POWER
SUPPLY
USB
F
XF MODULE
+
8.8.
1 2
1 2 1 2
3 4 5 6 7 8
11 12 13 14 15 16 17 18 19 20
DL1 DL2 DL3 DL4
DL9 DL10 DL11
DL12
SW3
DL14
BATTERY
SW1
SW2
DL13
DL5
DL6 DL7 DL8
ALARM
RESET
DL12
DL1 DL2 DL3DL4
DL6
DL7DL8
DL9
DL5
DL13
DL10 DL11
2EASY
OUT2
OUT1
LAMP LOCK MOT1 MOT2
+
-
+
-
IN1
IN2
IN4
IN5
GND
IN3
GND
+24
FCA
1
FCC
1
FCC
2
FCA
2
GND
GND
GND
ENC
1
+24
ENC
2
LED
R2
Tr
ansla
tion of the orig
inal instruc
tions
ENGLISH
7.4 RADIO CONTROLS - SLH/SLHLR
Memorise the first MASTER radio control on the board,
then add other radio controls that are required.
MEMORISING THE MASTER ON THE BOARD
A “MASTER” radio control has to be used. OPEN A and
OPEN B commands have to be memorised separately.
To check if it is a MASTER radio control
Press and hold down
a button and watch the LED:
- flashes briefly, then the light becomes
steady = MASTER
- turns on immediately with a steady light = NON
MASTER
L
Whenever a master is memorised on the board, any
SLH/SLHLR radio controls that are already in use are
disabled.
This memorisation procedure for the MASTER applies to the inte-
grated OmniDEC receiver combined with the 3-pin plug in module
(it allows OPEN A and OPEN B commands to be memorised).
If a 5-pin plug in receiver is used (only for OPEN A command), follow
the specific instructions.
MEMORISING OPEN A
1. Press the
++
(or
R1
) button on the board and release
it when
LED R1
starts to flash, for 20 s (time available
for the next steps).
2. Press buttons
P1
and
P2
simultaneously on the
radio control and release them when
LED
starts
to flash, for 8 s (time available for the next step).
3. On the radio control, held at approximately 50 cm
from the board, press button
P1
and check
LED R1
on the board:
it becomes steady for 1 s and then
switches off (memorisation complete).
4. Release the button.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
MEMORISING OPEN B
Proceed as for memorising OPEN A, using the
--
(or
R2
) button combined with
LED R2
and button
P2
on
the board.
ADDING RADIO CONTROLS
It is necessary a MASTER that is already in use. It is not neces-
sary to be close to the board.
OPEN A COMMAND
1. Press buttons
P1
and
P2
simultaneously on the
MASTER board that is already in use and release
them when
LED
starts to flash, for 8 s (time available
for the next step).
2. Press and hold down button
P1
and check the
LED
:
it becomes steady.
3. Without releasing the button, position the front of
radio control to be added so that it is in contact with
that of the master. Press and hold button
P1
on the
radio control to be memorised and check the
LED
: it
flashes twice and then switches off.
4. Release both.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
OPEN B COMMAND
Proceed as for copying OPEN A, using button
P2
at
steps 2 and 3.
Memorising OPEN A
MEMORISING OPEN B
Adding radio controls
Summary of Contents for E124
Page 1: ...E124 Translation of the original instructions...
Page 43: ......