background image

ATR833A-II / P/N 833-II (Axxx)-(Axxx) 

Operation and Installation 

 

 

25 

Doc.-No. 01.143A.010.71e / Revision 1.00 

3  CONFIGURATION 

A very long press of 

SET

 (5 seconds) accesses the configuration menu. 

The configuration menu is used for fundamental settings. 

To choose between the following settings, use the 

SET

 button: 

1.  SPACING 

Channel spacing 

2.  DISPLAY 

Display darkening (power save mode) 

3.  PTT SLCT 

PTT button selection 

4.  DUOWATCH  Dual Watch muting 

5.  EXTAUDIO 

Behaviour of the external audio input 

6.  MIC L TYP 

Microphone type left 

7.  MIC L std 

Microphone sensitivity left (for standard mic.) 

8.  MIC L dyn 

Microphone sensitivity left (for dynamic mic.) 

9.  MIC R TYP 

Microphone type right 

10- MIC R std 

Microphone sensitivity right (for standard mic.) 

11. MIC R dyn 

Microphone sensitivity right (for dynamic mic.) 

12. HEAD OUT 

Headset configuration 

13. AUTO ON 

Automatic power on with cockpit power 

14. FW 

Firmware version (Processor) 

15. SW 

Software version (Control Head) 

Return to the standard mode (

VOL

) is done by a short press of the 

I/O

DW



  or 

 

button  or  automatically  10  seconds  after  the  last  entry 

(time-out). 

The selection of the values is done with 

VOL/SEL

 turn knob. 

3.1  SPACING 

– Channel Spacing 

With  this  setting,  the  ATR833  can  be  configured  to  constrain  frequency 
selection  to  25  kHz  channels  only.  This  can  be  used  to  speed  up  the 
manual frequency input in areas where no 8.33 kHz channel spacing is 
used.  

See chapter 2.4.2 for further information on manual frequency input. 

Using  the 

VOL/SEL

  turn  knob  following  options  can  be  selected  in  this 

submenu: 

Summary of Contents for ZATR833A-II-OLED























































Reviews: