F.F. Group AG 125/1100E PRO, Original Instructions Manual

Page: 11 / 64

f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor
to the power line, make sure the switch is in the
OFF position and the electric voltage is rated the
same as the voltage stamped on the motor name-
plate. Running at a lower voltage will damage the
motor.
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for cutting, roughing and
brushing of metal and stone materials without the
use of water.
TECHNICAL DATA
Article number 44 826 44 827
Model AG 125/PRO 1100E 1200EC
Rated voltage
V 220-240
Hz 50/60
Rated power input W 1.100 1.200
Rated speed min
-1
4.000-
12.200
4.000-
12.200
Grinding disc diam -
eter, max.
mm 125
Thread of grinder
spindle
M14
Weight kg 2,0 2,1
Sound emission values determined according
to EN 60745-1, EN 60745-2-3
Typically the A-weighted noise levels of the product
are:
Sound pressure
level
dB(A) 90,2
Sound power level dB(A) 101,2
Uncertainty K dB 3
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to
EN 60745-1, EN 60745-2-3
Vibration level max:
a
h,AG
m/s 2 9,063
K m/s
2
1,5
NOISE/VIBRATION INFORMATION
The vibration level given in this information sheet
has been measured in accordance with a standard-
ized test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure. The declared
vibration emission level represents the main appli-
cations of the tool. However if the tool is used for
different applications, with different accessories or
insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main -
tain the tool and the accessories, keep the hands
warm, organization of work patterns.
IDENTIFICATION
1. On/Off switch
2. Spindle lock button
3. Auxiliary handle
4. Protective guard
5. Release lever for protection guard
6. Spindle
7. Clamping flange
8. Spanner
9. Mounting flange
10. Speed Preselection thumbwheel
USE
MOUNTING OF ACCESSORIES (E)
f
Clean spindle (6) and all parts to be mounted.
f
Tighten clamping flange (7) with spanner (8) while
pushing spindle-lock button (2) .
f
For removing accessories handle vice-versa.
MOUNTING OF AUXILIARY HANDLE (C)
Screw the auxiliary handle (3) on the right or left
of the machine head depending on the working
method.
REMOVING / MOUNTING / ADJUSTING OF PRO-
TECTIVE GUARD (B)
f
Open the guard by releasing the lever (5)
f
Place protective guard (4) on the spindle collar and
turn it to the required position (depending on the
work to be carried out).
f
Adjust protective guard (4) by pushing the lever
(5) .
BEFORE USING THE TOOL
f
Ensure that accessory is correctly mounted and
firmly tightened.
f
Check if accessory runs freely by turning it by hand.
f
Test-run tool for at least 60 seconds at highest no-
load speed in a safe position.
f
Stop immediately in case of considerable vibration
or other defects and check tool to determine the
cause.
SWITCHING ON AND OFF (D)
f
To start the power tool, push the on/off switch (1)
forward.
f
To lock the on/off switch (1) in position, push the
on/off switch (1) forward and down until it clicks
into place.
f
To switch off the power tool, release the on/off
switch (1) ; or, if the switch is locked, briefly push
the on/off switch (1) backward and down and then
release it.
English | 11
www.ffgroup-tools.com
AG 125/1100E PRO | AG 125/1200EC PRO