YCS 100 • Installation and Operation
Installation and Operation, cont’d
2-10
YCS 100 • Installation and Operation
2-11
Extron
PMK 350
Multi-product Projector
Mounting Kit
Cover Sheet
Front Plate
Rear Plate
U-bolt
L-shaped
Bracket
Contoured
Base
Extron
Power Supply
Extron
YCS 100
Transcoder
Figure 2-10 — Projector-mounting the YCS 100
using the PMK 350 Projector Mount Kit
7
.
Align the two slotted holes in the bottom of the L-shaped
bracket with the two slotted holes in the base of the
PMK 350, on either side of the opening for the pole.
Attach the L-bracket to the base by inserting two provided
6-32 x 5/16" screws through the aligned slots.
8
.
Insert the two legs of the provided square U-bolt through
the following parts in the order they are listed below:
a
. The slotted holes on the back side of the bracket mount
plate
b
. The round holes in the rubberized contour base
c
. The round holes in the L-shaped bracket
•
For a typical (1.5" to 2.0" diameter) pole
— You can use
the supplied square U-bolt, which fi ts a typical ceiling
pole.
•
For a smaller pole
— Locally obtain a square U-bolt
that fi ts your ceiling pole. The slotted holes on the
bracket can accommodate a square U-bolt for pole sizes
from 1.0" to 2.0" in diameter.
9
.
Move the PMK 350 up to the desired location on the ceiling
pole, as close to the ceiling as desired.
3
. Affi x the supplied rubber pad to the side of the U-bolt
clamping plate that the projector pole contacts.
4
.
Place the U-bolt around the ceiling pole and insert the two
legs of the U-bolt through the slotted holes on the bracket’s
mounting plate, then through the round holes on the
backing brace.
•
For a typical (1.5" to 2.0" diameter) pole
— You can use
the supplied square U-bolt, which fi ts a typical ceiling
pole.
•
For a smaller or larger pole
— Locally obtain a square
U-bolt that fi ts your ceiling pole. The slotted holes on
the bracket can accommodate a square U-bolt for pole
sizes from 1.0" to 2.5" in diameter.
5
.
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers. Tighten the hex nuts just
enough that they can be loosened by hand.
Using the PMK 350 Projector Mount Kit
The PMK 350 Low Profi le Projector Mount Kit is an above-
projector mounting kit that attaches to a 1" to 2" diameter
projector mounting pole. It can hold more than one device,
in a variety of sizes. The PMK 350 is available in black
(part #70-563-02) or white (part #70-563-03).
Follow these steps to mount the YCS 100 on the PMK 350
bracket as follows:
1
.
Remove the front and back panels from the
PMK 350, using an Extron Tweeker or other small Philips
screwdriver. (Retain the screws to reattach the plates when
you are fi nished.)
2
.
Remove any rubber feet from the bottom of the YCS 100.
3
.
Secure the YCS to one side of the mounting bracket,
using two of the supplied 4-40 x 3/16" screws in opposite
(diagonal) corners.
4
.
Using the two included tie wraps, strap the YCS power
supply to the PMK 350 bracket.
5.
Place the bracket around the projector ceiling mounting
pole as shown in fi gure 2-10.
6
.
Place the rubberized contoured base against the pole and
opposite the back plate. The pole should fi t snugly into the
depression in the center of the contoured base.
Summary of Contents for YCS 100
Page 3: ......
