background image

ATTENTION:

• 

The installation must always be in accordance with the applicable provisions of 
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical Code 
part 1, section 16.

• 

Cette installation doit toujours être en accord avec les mesures qui s’applique au 
National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical Code, 
partie 1, section 16.

• 

The power supply shall not be permanently fixed to the building structure or similar 
structure.

• 

La source d’alimentation ne devra pas être fixée de façon permanente à une structure 
de bâtiment ou à une structure similaire.

An Extron IPL Pro control processor must also be connected to the same network domain as the 
TouchLink Pro touchpanel. See the 

www.extron.com

 for a list of suggested models.

The network port has two LEDs. The green LED lights steadily to indicate that the touchpanel is 
connected correctly to a network. The yellow LED flashes to indicate that data is being passed to 
or from the touchpanel.

E

 

Mounting holes

 (4)

 (TLP Pro 1022M only) (see 

figure 3

) — for wall mounting (see 

Wall 

Mounting

 on page 18). 

F

 

Status light

 (TLP Pro 1022T only) — can be programmed to provide system feedback.

• 

Light red or green

• 

Blink or solidly lit

For information about programming this light, see the 

Global Configurator Help File

.

G

 

VESA mounting holes

 (4)

 (TLP Pro 1022T only)— for use with the Extron LPVM-1 (see 

VESA Mounting

 on page 22).

H

 

Base attachment hinges

 (2)

 (TLP Pro 1022T only)— Secure the base to the touchpanel. 

For VESA mounting, remove the base by unscrewing the hinges (see 

VESA Mounting

 on 

page 22).

 

TLP Pro 1022 Series • Panel Features

7

Summary of Contents for TLP Pro 1022T


































Reviews: