4
68-2405-50 Rev. B
05 14
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2014 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
TLP PRO 720T and TLP PRO 1020T • Setup Guide (Continued)
A
Power connector
— connect a 12 VDC, 1.0 A power supply (not provided) to this DC plug connector.
ATTENTION:
•
The TLP Pro 720T and TLP Pro 1020T can use a 12 VDC power supply and are also Power over Ethernet (PoE
802.3af, class 3) compliant. Do not connect either power supply before reading the Attention in the Power section
of the
TLP Pro 720 Series and TLP Pro 1020 Series User Guide
.
•
Le TLP Pro 720T et le TLP Pro 1020T peut utiliser une source d’alimentation externe 12 Vcc, et est également
compatible avec l’alimentation POE via Ethernet (PoE 802.3af, classe 3). Ne branchez pas de sources
d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power Supply » du
TLP Pro 720 and
TLP Pro 1020 Series User Guide
.
NOTES:
•
The TLP Pro 720T and TLP Pro 1020T are shipped without a power supply. Either the 12 VDC, 1.0 A power supply
or the power injector must be purchased separately.
•
If a 12 VDC and a PoE power injector are both connected to the TLP Pro 720T or TLP Pro 1020T, the power
injector takes precedence. If a PoE power loss is detected, the touchpanel switches seamlessly to the 12 VDC
supply without needing a system reboot.
B
Network and Power over Ethernet Connector
— is in the top of the recessed area (see the arrows in figure 6). Connect
the touchpanel to the LAN using a twisted pair cable, terminated with an RJ-45 connector. The connector can be used with a
PoE power injector (not provided).
An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.
C
Menu button
— activates the setup menu and calibration screen (see below).
D
Reset button
— pressing the reset button allows the unit to be reset in any of three different modes. For full information
about the modes, see the
TLP Pro 720 Series and TLP Pro 1020 Series User Guide
.
E
Reset LED
— provides feedback about the reset status when the user presses the reset button.
F
VESA mounting holes (4)
— for use with the Extron LPVM-1 (see
VESA Mounting
on page 2).
Reset Modes: a Brief Summary
The TLP Pro 720T and TLP Pro 1020T offer the following reset modes:
•
Use factory firmware:
Press and hold the Reset button (figure 6,
D
) while applying power to the unit. Use this
mode to replace firmware in the event of firmware failure.
•
Reset All IP Settings:
Press and hold the Reset button for 6 seconds. After the Reset LED (figure 6,
E
) flashes
twice, release and momentarily press the Reset button. Use this mode to reset all network
settings without affecting user-loaded files.
•
Reset to Factory Defaults:
Press and hold the Reset button for 9 seconds. After the Reset LED flashes three times,
release and momentarily press the Reset button. Use this mode to return the interface to
factory default settings.
Setup Menu
Press the menu button (
C
in figure 6, on the previous page) to open the
setup menu. Select any of the five available screens (
Status
,
Network
,
Display
,
Audio
, and
Advanced
) by pressing the appropriate button in
the navigation bar at the top of the screen (for more information, see the
TLP Pro 720 and TLP Pro 1020 Series User Guide
).
Figure 7 shows the setup menu for the TLP Pro 720T. The setup menu for
the TLP Pro 1020T is identical.
Press the menu button for at least 3 seconds to open the calibration
screen. Follow the on-screen instructions.
Figure 7.
Setup Menu: Status page for TLP Pro 720T
Status
Display
Audio
Advanced
Exit
Network
Info
Model:
TLP Pro 720T
Part Number: 60-1395-02
Firmware
Version:
1.00
PoE Status:
On
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLP-AB-CD-EF
Display
Resolution:
Project:
Sleep Timer:
800x480
N/A
5 Minutes
Audio
Master Volume:
Master Mute:
Off
99
Advanced
Controller IP:
N/A
Project Size:
N/A