manualshive.com logo in svg

Extron electronics TLP 710MV, User Manual, Page: 21 / 54

Share
Download
Extron electronics TLP 710MV User Manual Download Page 21

The Sleep timer determines how long the panel will be inactive before it enters Sleep 
mode, when the screen goes dark to save power. The time can be changed from 0 to 
50,000 seconds (in 10-second increments). The time that is currently selected is shown 
above the buttons.
The screen may need a high level of backlighting for readability when ambient lighting is 

high. With low ambient lighting, the backlighting should be low.
Auto Backlight provides a suitable amount of backlighting that is automatically calculated 

from the amount of ambient light detected by the light detector.

When Auto Backlight is set to Off, Backlight allows the backlighting to be set manually 

from 0 to 100 percent.

NOTE:

  When Auto Backlight is set to 

On

, the value of Backlight can be changed 

but this does not affect the amount of backlighting until Auto Backlight is 

inactivated.

Wake on Motion activates the panel from Sleep mode when motion is detected near the 

unit.

Use the on-screen buttons to toggle the Auto Backlight or Wake on Motion options 

between Off and On.

Volume Screen

Exit

Master: 120

Click: 120

Sounds: 120

Down

Up

Down

Up

Down

Up

Down

Up

Line In: 120

Main

Volume

Time

Network

Video

Figure 14. 

Volume Screen

Press the 

Down

 or 

Up

 buttons to highlight one of the adjustable audio features. Use the 

Down

 and 

Up

 buttons to adjust the following settings. 

• 

Master volume (between 0 and 255; default 120) sets the maximum volume for all 
the other sound volume settings. For example, if the master volume is set to 200 
(approximately 80 percent of maximum), even when the Line In volume is set to 255 
(maximum), it is equivalent to only 80 percent of maximum.

• 

Click (between 0 and 255; default 120) sets the volume for audible feedback that 
accompanies events such as a screen button being pressed.

• 

Sounds (between 0 and 255; default 120) sets the volume of audio from any audio 
file playback.

• 

Line In (between 0 and 255; default 120) sets the volume of the audio signal received 

through the line in from an Extron MTP transmitter.

 

TLP 710MV and TLP 710TV • Initial Calibration

15

Summary of Contents for TLP 710MV























































Reviews:

No comments