Extron electronics SW2HD 4K PLUS, Setup Manual, Page: 4 / 4

4 68-2940-50 Rev. A
1 1 17
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
www.extron.com
Front Panel Features
SW2 HD 4K PLUS
HDMI SWITCHER
1
R
CONFIG
SIGNAL
INPUTS
INPUTS
OUTPUT
1 2
HDCP
2
AUTO
SWITCH
C C
D D
F
B B A
E
Figure 4.
SW2 HD 4K
PLUS
Front Panel
SW4 HD 4K PLUS
HDMI SWITCHER
R
CONFIG
AUTO
SWITCH
1
INPUTS
2 3 4 SIGNAL
INPUTS OUTPUT
1 2 3 4
HDCP
F
B
E
C
D
A
Figure 5. SW4 HD 4K
PLUS
Front Panel
A
AUTO SWITCH LED — Lights when auto-input switching is in effect. When auto-input switching is enable, the
switcher automatically switches to the highest-number input with an active video signal.
B
USB CONFIG port — Connect a USB cable (USB A to mini-B) between your computer and this female USB
mini-B port to configure and control the switcher via SIS commands or PCS, and to update the firmware.
C
SIGNAL LEDs — The LEDs labeled INPUTS each light when the corresponding input is connected to a device
that has power. The LED labeled OUTPUT lights when the output is connected to a device that has power.
D
HDCP LEDs
•
Input LEDs — Light if the connected sources are HDCP encrypted and have been authenticated by the
switcher inputs.
NOTE: If the source device connected to the selected input is HDCP encrypted (requires HDCP
authentication), the corresponding signal LED may not light unless HDCP has been authenticated.
•
Output LED — Lights when the currently selected input requires HDCP and the connected output device
has been successfully authenticated.
NOTE: HDCP is re-authenticated on the output whenever a new input is selected.
E
Input selection buttons — Press one of these buttons to select an input to switch to the output. The LED at
the right of each button lights when the corresponding input is selected. If auto-input switching is in effect, these
buttons are disabled, but the LEDs continue to light to indicate the selected input. The input buttons are also
used to initiate a system reset and to enable and disable front panel lockout (see the
SW HD 4K PLUS Series
User Guide for more information).
F
Reset button — This button initiates two levels of reset of the switcher. For the different reset levels, press and
hold the button while the switcher is running or while you power up the switcher. (For more information about
reset levels, see the
SW HD 4K PLUS User Guide at
www.extron.com
.)
A
AUTO SWITCH LED
B
USB CONFIG port
C
SIGNAL LEDs
D
HDCP LEDs
E
Input selection buttons
F
Reset button