Extron electronics MultiMatrix SMX System Setup Manual Download Page 11

Page: 11 / 48

SMX System MultiMatrix Switcher • Installation

Unbalanced Stereo Input

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleeves

Tip

Sleeve

Tip

Unbalanced Mono Input

Balanced Mono Input

(high impedance)

Tip

Ring

Sleeve

Tip

Sleeve

Figure 3.

Audio Input Captive Screw Wiring

NOTES:

•

A mono audio connector consists of the tip and sleeve,
whereas a stereo audio connector consists of the tip,
ring, and sleeve. The tip, ring, and sleeve wires are
also shown in

figure 4

(balanced inputs).

•

See the

SMX User Guide

for details about setting up

the audio.

Tip (+)

Sleeve ( )

Ring (-)

Tip (+)

RCA Connector

3.5 mm Stereo Plug Connector

(balanced)

Figure 4.

Audio Connectors

Audio output connectors

—

Connect audio output devices to the

3.5 mm, 5-pole captive screw connectors (up to two groups of eight
sets possible). The connectors output unamplified, line level audio
(see

figure 5

for wiring details).

Balanced Audio Output

Tip

Ring

Tip

Ring

Sleeves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Sleeves

Figure 5.

Audio Output Captive Screw Wiring

CAUTION:

For unbalanced audio, connect the sleeves to the
center contact ground. Do not connect the sleeves to
the negative (-) contacts.

Summary of Contents for MultiMatrix SMX System

















































Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands

Extron electronics MultiMatrix SMX System, Setup Manual

Search results

Summary of Contents for MultiMatrix SMX System

Reviews:

Related manuals for MultiMatrix SMX System

Brands by name

Popular brands