DTP HDMI 230 Tx Rear Panel
DTP HDMI 230 Rx Rear Panel
Front Panel
DTP HDMI 230 Rx
OVER DTP
RS-232
IR
Tx Rx
Tx Rx
G
L
R
POWER
12V
0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
AUDIO
INPUTS
OVER DTP
RS-232
IR
Tx Rx
Tx Rx
G
POWER
12V
0.7A MAX
SIG LINK
DTP OUT
3
6
3
7
7
1
5
4
4
2
DTP HDMI 230 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron DTP HDMI 230 digital video extender. The DTP HDMI 230 transmitter and receiver pair can
extend an HDCP-compliant HDMI signal up to 230 feet (70 m).
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the Tx and Rx units as required.
Step 2 — Connections
a
HDMI Input connector (Tx)
— Connect an HDMI
cable
between this port and the HDMI output port of
the digital video
source.
NOTE:
See the “
LockIt™ Lacing Brackets
“on the back of this guide for to
securely fasten the input HDMI connector to the transmitter.
b
Audio input (Tx)
— Connect an unbalanced stereo audio source to this 3.5 mm mini
stereo jack for an analog audio input.
c
RS-232 and IR connectors
— To pass serial or infrared data or control signals, such as
serial control of a projector, connect the master device to the transmitter and the slave
device to the receiver via the RS-232 and IR captive screw connectors on both units.
d
DTP RJ-45 connectors
— Connect transmitter DTP Out to receiver DTP In.
Extron recommends that you terminate both cable ends in accordance with the
following specifications, at a minimum:
z
TIA/EIA T 568 B
z
CAT 6A, shielded
z
24 AWG, solid conductor
ATTENTION:
Do not connect these devices to a computer data or telecommunications
network.
Signal LED
— Lights when the unit is receiving a TMDS clock signal on the HDMI input (transmitter) or
any valid signal on the DTP In connector (receiver).
Link LED
— Lights when a valid link is established between the units on the DTP cable.
e
HDMI Output connector (Rx)
— Connect a display with an HDMI input for display of the
transmitted direct digital image.
NOTE:
See the “
LockIt™ Lacing Brackets
“on the back of this guide for to
securely fasten the output HDMI connector to the receiver.
f
Audio Output connector (Rx)
— Connect a balanced or unbalanced stereo or mono audio
device to the receiver via the Audio captive screw connector. See the drawing below.
Unbalanced Stereo Output
Balanced Stereo Output
Do not tin the wires!
Tip
Ring
Tip
Ring
Sleeves
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
ATTENTION:
Connect the sleeves to the ground contact.
DO NOT
connect the sleeves to the negative (-) contacts
.
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568 B
TP Wires
12345678
Pins:
5
Pin
1
2
3
6
7
8
4
Ground
Receive pin on connected unit
Transmit pin on connected unit
Connected RS-232
and IR Device Pins
Tx/Rx
Pins
Receive pin on connected unit
Transmit pin on connected unit
RS-232
IR
Tx
Rx
Tx
Rx
G
L
R
AUDIO
OUTPUTS
AUDIO
INPUTS
