Extron electronics HDMI 201 A D Tx User Manual Download Page 12

HDMI 201 Tx/Rx • Installation and Operation

Installation and Operation, cont’d

2-8

HDMI 201 Tx/Rx • Installation and Operation

 

2-9

N

 

The PMK 300 has a hole in the bottom plate that 

allows the projector pole to be inserted through the 

center of the plate (figure 2-6), rather than outside of 

the plate (figure 2-5).  To install the PMK 300 in this 

configuration, slide the bracket up from the bottom of the 

pole before the projector is installed on the pole.

 

U-Bolt

Extron
PMK 300

Multi-product Pole
Mount Kit

Bracket
Brace

Figure 2-6 — Projector pole on the inside

4

Place the contoured bracket brace against the pole and 

opposite the back plate.  The pole should fit snugly into the 

depression in the center of the bracket brace.

5

Place the U-bolt around the ceiling pole.  Insert the 

two legs of the U-bolt through the round holes on the 

contoured bracket brace and then through the slotted holes 

on the bracket’s mounting plate.

N

 

The supplied U-bolt fits a typical (1.5" to 2.0" diameter) 

ceiling pole.

6

Secure the bracket to the U-bolt with the included hex 

nuts, washers, and lock washers.  Tighten the hex nuts just 

enough that they can be loosened by hand.

PMK 350 mounting

Mount the receiver to a PMK 350 bracket as follows:

1

Remove the front and rear plates from the PMK 350 
(figure 2-7), using an Extron Tweeker or 

a #2 Philips 

screwdriver

.  Retain the screws to reattach the plates when 

you are finished.

Extron
PMK 350

Multi-product Pole
Mount Kit

Cover Sheet

Front Plate

Rear Plate

U-bolt

L-shaped
Bracket

Contoured
Base

Extron

Power Supply

Extron
Quarter-rack
Sized Product

Figure 2-7 — PMK 350 projector mounting a receiver

2

If necessary, remove the feet from the bottom of the 

receiver.

3

Secure the receiver to one side of the mounting tray, 

using two of the supplied 4-40 x 3/16" screws in opposite 

(diagonal) corners.

4

If power supply is connected to the receiver, use the 

two included tie wraps to strap the power supply to the 

bracket.

5

Place the PMK 350 around the projector ceiling mounting 

pole (figure 2-7).

Summary of Contents for HDMI 201 A D Tx





























Reviews: