DTP2 T 212 • Setup Guide
The Extron DTP2 T 212 is a two input HDMI switcher with two simultaneous outputs for 4K video signals. The DTP2 T 212 extends
signals 330 feet (100 meters) and features two HDMI inputs, one local HDMI output, and one TP output. The TP output extends
digital video and audio, remote power, analog audio, and bidirectional RS-232 and IR. The switcher also features EDID Minder
®
,
which maintains continuous EDID communication with connected devices and ensures the HDMI sources power up properly and
maintains correct video output, and Key Minder to manage HDCP
®
. The switcher supports computer and video resolutions up
to 2560x1600 @ 60 Hz and 4K UHD @ 60 Hz 4:4:4, with a maximum data rate of 18.0 Gbps and HDCP 2.2. This guide provides
instructions for an experienced installer to set up and operate this switcher.
The diagram below shows a typical application for a DTP2 T 212 switcher. For full installation, configuration, and operation details,
see the
DTP2 T 212 User Guide
, available at
.
DTP2 R 212
Switcher DA Extender
OUTPUTS
POWER
12V
0.8A MAX
SIG LINK
DTP2 IN
RS-232
IR
Tx Rx
Tx Rx
G
L
R
AUDIO
OVER DTP2
Rx G
Tx
RS-232
IR
Rx
Tx
OVER TP
POWER
12V
2.0A MAX
RS-232
CONTACT /
TALLY
1
C G T
C G
G
Rx
Tx
+V
T
2
1
AUDIO
2
A
B
REMOTE
INPUTS
OUTPUTS
SIG LINK
OUT
DTP
HDBT
OFF
SEND
POWER
RS-232
RS-232
HDBT
Video/
Control
MLC Plus 100
MediaLink Plus Controller
Extron
DTP2 T 212
Switcher DA Extender
HDBT
Projector
WiFi
1 2 3 4
Laptop
PC
Local Monitor
HDMI
HDMI
HDMI
RS-232
Control
HDMI
DISPLAY
VOLUME
Extron
ON
OFF
PC
VGA
DOC
CAM
MUTE
Figure 1.
Application Diagram of the DTP2 T 212
Rear Panel Features and Connections
Rx G
Tx
RS-232
IR
Rx
Tx
OVER TP
POWER
12V
2.0A MAX
RS-232
CONTACT /
TALLY
1
C G T
C G
G
Rx
Tx
+V
T
2
1
AUDIO
2
A
B
REMOTE
INPUTS
OUTPUT
S
SIG LINK
OUT
DTP
HDBT
OFF
SEND
POWER
J
J
J
J
I
I
I
H
H
H
G
G
G
F
F
F
E
E
E
D
D
D
C
C
C
B
B
B
A
A
A
Power inlet
TP function toggle switch
B
Audio input
Over TP RS-232 and IR switching port
C
HDMI input
SEND POWER toggle switch
D
HDMI output
Contact/Tally port
TP2 RJ-45 output
Remote RS-232 port
Figure 2.
DTP2 T 212 Rear Panel
Installation Steps
1.
Turn off and disconnect all of the equipment
from their power sources.
2.
Mount the switcher
on a rack shelf or furniture (optional).
3.
Connect HDMI input sources
to one or both of the HDMI inputs (see figure 1,
C
).
NOTE:
Use provided LockIt lacing brackets to secure the HDMI cables to the ports to reduce stress on the HDMI connectors
and prevent signal loss due to loose cable connections (see
4.
Connect an HDMI device
to the HDMI output (
D
). By default, the EDID of this device is stored at the HDMI output.
5.
Connect an unbalanced stereo audio source to the 3.5 mm mini stereo input
(
B
) for analog audio input (optional). Analog
audio input can be configured to be embedded in the HDMI signal or transmitted separately. It is available for either selected input.
1
2
1
