Extron electronics DTP2 R 212 Series, User Manual

Page: 15 / 68

DTP2 R 212 Series • Installation 7
• If the transmitting device is in the Extron DTP2 series and you setting up the
DTP2 R 212 SA (amplifier model), you
can only set the receiver to send power to
the transmitter:
• Set the receiver SEND POWER switch of the receiver (see figure 3 ,
E
on page 7) to the “UP” (SEND POWER) position (see figure 5 on
page 10).
• Set the transmitter SEND POWER switch of the transmitter (see figure 3 ,
E
)
to the “DOWN” (OFF) position (see figure 5 ).
•
If the transmitting device is in the Extron Legacy DTP series and not the DTP2
series, set the
SEND POWER switches of both devices to the “DOWN” (OFF)
position (see figure 4 on page 9).
6. Connect Over DTP RS-232 and IR control. Connect a serial RS‑232 signal, a
modulated IR signal, or both into this 3.5 mm, 5‑pole captive screw port (see figure 3 ,
C
) for bidirectional RS‑232 and IR communication (see Over DTP2 RS-232 and IR
Control on page 16 for connection procedures).
7. Connect control devices.
Connect your computer to one of the following ports to
configure and control the device via SIS commands or PCS:
•
RS-232 port — This 3‑pole RS‑232 port (see figure 3 ,
L
) for serial RS‑232
control (see Display and Remote RS-232 Control on page 15 for connection
procedures).
• Config port — USB mini‑B port for USB control (see Connecting to the USB
Port on page 20 for connection procedures).
• LAN (Ethernet) port — Connect an Ethernet cable for LAN control. LEDs on
the connector indicate link and activity status (see LAN Connector Wiring on
page 13 for connection wiring).
8. Power on the output display.
9. Connect power to the switcher (see Powering on the Receiver on page 19).
10. (Optional) Configure EDID Minder (see the DTP2 R 212 PCS Help File).
11. Power on the source devices.
Rear Panel Features
1
2
Rx G Tx
HDMI HDMI
RS-232
DTP2 R 212
IR
Rx Tx
OVER DTP2
Rx G Tx
RS-232
DISPLAY POWER
12V
2.0 A MAX
RS-232
Rx Tx G
INPUTS
OUTPUT
LAN
REMOTE
L R
OFF
SEND
POWER
R
SIG LINK
DTP2 IN
CLASS 2
WIRING
4/8 OHM
1
2
L
R
Rx G Tx
HDMI HDMI
RS-232 IR
Rx Tx
OVER DTP2
Rx G Tx
RS-232
DISPLAY
POWER
12V
3.0 A MAX RS-232
Rx Tx G
INPUTS OUTPUT
C V G
10V 50mA
L R
VOL
REMOTE
R
DTP2 R 212 SA
LAN
OFF
SEND POWER
SIG LINK
DTP2 IN
B D C A I J L K G F H M N E
* * *
A
Power Inlet
H
Amplified audio output (SA models)
B
HDMI input
I
Display control
C
OVER DTP2 control
J
Remote amplified volume control (SA models)
D
DTP2 IN RJ-45 port
K
Switch for volume control (SA models)
E
Send Power toggle switch
L
Remote RS-232 port
F
HDMI output
M
LAN (Ethernet) port
G
Audio output
N
Reset button
Figure 3. Rear Panel Features
3