1
IMPO
RTAN
T:
Go to ww
w.extr
on.com
for the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
DSC HD-HD 4K A Setup Guide
The Extron DSC HD-HD 4K A is a high performance, HDCP 1.4 and 2.2 compliant scaler capable of processing HDMI resolutions
up to 4K @ 30 Hz with full 4:4:4 signal processing and 4K @ 60 Hz with 4:2:0. It features HDMI 1.4 and 2.0 connections that
support data rates up to 8.91 Gbps. This setup guide provides step-by-step instructions for an experienced user to set up and
configure the DSC HD-HD 4K A. It also describes basic operations using
front panel controls
, the
OSD menu system
, and
Simple Instruction Set (SIS
™
)
commands.
Installation
ATTENTION:
•
Installation and service must be performed by authorized personnel only.
•
L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
NOTE:
For full installation, configuration, menus, connector wiring, and operation details, see the
DSC HD-HD 4K A Series
User Guide
, available at
www.extron.com
.
Rear Panel Features
RS -232
RESET
LAN
AUDIO IN
REMOTE
AUDIO OUT
50-60 Hz
100-240VAC ~ 0.7 A MAX
DSC HD-HD 4K A
L
R
L
R
Tx Rx G
A
A
G
G
D
D
F
F
HDMI
INPUT
HDMI
OUTPUT
B
B
C
C
H
H I
I
E
E
A
AC power connector
D
Analog audio input connector
G
Remote RS-232 connector
B
HDMI input connector
E
Analog audio output connector
H
Reset LED
C
HDMI output connector
F
Ethernet LAN connector
I
Reset button
Figure 1.
DSC HD-HD 4K A Rear Panel
Setup Overview
1.
Disconnect power
— Turn off or disconnect all equipment power sources.
2.
Mount the unit (optional)
— Mount the DSC HD-HD 4K HD A either in a rack using shelf mounting bracket kits (available
at
www.extron.com
) or under furniture using furniture mounting brackets (see the instructions provided with the kit).
Alternatively, attach the four provided rubber feet at the corners of the unit and place it on a table top.
3.
Connect the HDMI video input and output
— Connect an HDMI video source to the HDMI input connector (
B
) and a
display to the HDMI output (
C
)
connector. Secure each HDMI device to the connector with a provided LockIt
®
bracket.
4.
Connect an audio input device (optional)
— Connect
an analog audio source to the 5-pole captive screw Audio
In connector (
D
) to embed balanced or unbalanced
analog audio in the HDMI output signal.
5.
Connect an audio output device (optional)
—
Connect an audio output device to the 5-pole captive
screw Audio Out connector (
E
) for analog audio output.
6.
Connect a control device
— For remote control,
connect a computer or control system to any of these ports:
•
Remote RS-232
— This 3-pole captive screw RS-232 connector (
G
) enables serial control via SIS
commands. RS-232 protocol for this port is 9600 baud, 1 stop bit, no parity, 8 data bits, and no flow control.
•
USB
— This front panel USB mini-B port (See
figure 2
,
B
, on the next page) enables configuration and
control via SIS commands or the Extron PCS Configuration software.
•
LAN
— This RJ-45 Ethernet jack (
F
) connects the unit to a network, enabling you to configure the DSC via SIS
commands, PCS, or the device internal web page.
Unbalanced Stereo Input
Balanced Stereo Input
Tip
Ring
Tip
Ring
Sleeves
Do not tin the wires!
Tip
Sleeve
Sleeve
Tip
LR
LR
inch (5 mm) MAX.
Balanced Audio Output
Tip
Ring
Tip
Ring
Sleeves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Do not tin the wires!
inch (5 mm) MAX.
RS-232
Tx Rx G