Extreme Networks ExtremeWireless 31012 Quick Reference Download Page 2

ExtremeWireless

TM

 

Access Points

Quick Reference

P/N 31012 WS-AP3935i-FCC

P/N 31013 WS-AP3935i-ROW

P/N 31014 WS-AP3935e-FCC

P/N 31015 WS-AP3935e-ROW

Notice 

Copyright © 2015 Extreme Networks, Inc. All Rights Reserved.

Legal Notices

Extreme Networks, Inc. reserves the right to make changes in specifications 
and other information contained in this document and its website without 
prior notice. The reader should in all cases consult representatives of 
Extreme Networks to determine whether any such changes have been 
made.
The hardware, firmware, software or any specifications described or referred 
to in this document are subject to change without notice.

Trademarks

Extreme Networks and the Extreme Networks logo are trademarks or 
registered trademarks of Extreme Networks, Inc. in the United States and/or 
other countries. 
All other names (including any product names) mentioned in this document 
are the property of their respective owners and may be trademarks or 
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see: 

www.extremenetworks.com/company/legal/trademarks/

Documentation & Support

For product support, including documentation, visit: 

www.extremenetworks.com/support/ 

Contact

Extreme Networks, Inc. 
145 Rio Robles
San Jose, CA 95134 USA
Tel: +1 408-579-2800
Toll-free: +1 888-257-3000

Regulatory and Compliance Information

Safety Guidelines

This section contains notices that are intended to protect your personal 
safety and prevent damage to the equipment.
Suitable for use in environmental air space in accordance with Section 
300.22.C of the National Electrical Code, and Sections 2-128, 12-010(3) and 
12-100 of the Canadian Electrical Code, Part 1,C22.1.
Convient à l'espace de ventilation environnemental, conformément à la 
section 300.22.C du Code national de l'électricité et aux sections 2-128, 12-
010(3) et 12-100 du Code canadien de l'électricité, partie 1, C22.1.

Qualified Personnel:

Federal Communications Commission (FCC) Notice 

This device complies with Part 15 of the FCC rules. Operation is subject to 
the following two conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
The antennas used for this transmitter must be installed to provide a 
separation distance of at least 25 cm from all persons and must not be co-
located or operating in conjunction with another antenna or transmitter.

Industry Canada Notice 

This device complies with Industry Canada license-exempt RSS standard(s). 
Operation is subject to the following two conditions: (1) this device may not 
cause interference, and (2) this device must accept any interference, 
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables 
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux 
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) 
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, 
même si le brouillage est susceptible d'en compromettre le fonctionnement.
This radio transmitter (IC: 4141B-4411AC) has been approved by Industry 
Canada to operate with the antenna types listed below with the maximum 

Electrical Hazard: 

Only qualified personnel should perform 

installation procedures. Within the context of the safety 
notes in this documentation, qualified persons are defined 
as persons who are authorized to commission, ground and 
label devices, systems, and circuits in accordance with 
established safety practices and standards. A qualified 
person understands the requirements and risks involved 
with installing outdoor electrical equipment in accordance 
with national codes.

Caution: 

Connect the equipment to Intra-Building networks 

only. Do not route cables outside.

Attention:

 Connecter l'équipement à des réseaux intra- 

bâtiment seulement . Ne pas acheminer les câbles à 
l'extérieur.

Note: 

Changes or modifications made to this device which 

are not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the 
equipment.

permissible gain and required antenna impedance for each antenna type 
indicated. Antenna types not included in this list, having a gain greater than 
the maximum gain indicated for that type, are strictly prohibited for use with 
this device. 

Le présent émetteur radio (IC: 4141B-4411AC) a été approuvé par Industrie 
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et 
ayant un gain admissible maximal et l'impédance requise pour chaque type 
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain 
est supérieur au gain maximal indiqué, sont strictement interdits pour 
l'exploitation de l'émetteur.

Antenna List:

Note:

 All antennas use an RP SMA Male connector.

The antennas used for this transmitter must be installed to provide a 
separation distance of at least 34 cm from all persons and must not be co-
located or operating in conjunction with another antenna or transmitter.

Cet équipement est conforme aux limites d'exposition aux rayonnements IC 
établies pour un environnement non contrôlé. Cet équipement doit être 
installé et utilisé avec un minimum de 34 cm de distance entre la source de 
rayonnement et votre corps.

Dynamic Frequency Selection (DFS) for devices operating in the bands 
5250- 5350 MHz,
5470-5600 MHz and 5650-5725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant 
dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz

The device for operation in the band 5150-5250 MHz is only for indoor use to 
reduce the potential for harmful interference to co-channel mobile satellite 
systems.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés 
uniquement pour une utilisation à l'intérieur afin de réduire les risques de 
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les 
mêmes canaux.

The maximum antenna gain permitted for devices in the bands 5250-5350 
MHz and 5470-5725 MHz shall be such that the equipment still complies 
with the e.i.r.p. limit.
le gain maximal d'antenne permis pour les dispositifs utilisant les bandes 
5250-5350 MHz et
5470-5725 MHz doit se conformer à la limite de p.i.r.e.

The maximum antenna gain permitted for devices in the band 5725-5850 
MHz shall be such that the equipment still complies with the e.i.r.p. limits 
specified for point-to-point and non-point-to-point operation as 
appropriate.
le gain maximal d'antenne permis (pour les dispositifs utilisant la bande 
5725-5850 MHz)
doit se conformer à la limite de p.i.r.e. spécifiée pour l'exploitation point à 
point et non point à point, selon le cas.

For product available in the USA/Canada market, only channel 1~11 can be 
operated. Selection of other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le 
canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas 
possible.
High-power radars are allocated as primary users (i.e. priority users) of the 
bands 5250-5350 MHz and 5650-5850 MHz and that these radars could 
cause interference and/or damage to LE-LAN devices. 
Les radars à haute puissance sont désignés comme utilisateurs principaux 
(c. utilisateurs prioritaires ) des bandes 5250-5350 MHz et 5650-5850 MHz 
et que ces radars pourraient provoquer des interférences et / ou 
endommager les appareils LE- LAN.

Hazardous Substances

This product complies with the requirements of Directive 2011/65/EU of the 
European Parliament and of the Council of 8 June 2011 on the restriction of 
the use of certain hazardous substances in electrical and electronic 
equipment.

Part No.

(Short Description)

Frequency 

Band

Antenna 

Type

2.4G
Gain

5G

Gain

30702 (WS-AI-DQ05120)

2.4G/5G

Sector

5.5

5.5

30703 (WS-AI-5Q04060)

5G

Sector

N/A

4

30704 (WS-AI-2Q05060)

2.4G

Sector

5

N/A

30705 (WS-AI-DE07025)

2.4G/5G

Sector

7.5

6.5

30706 (WS-AI-5Q05025)

5G

Sector

N/A

4.5

30707 (WS-AI-DE10055)

2.4G/5G

Sector

10.5

7.5

30709 (WS-ANT-2DIP-4)

2.4G

DIPOLE

4.66

N/A

30710 (WS-ANT-5DIP-4)

5G

DIPOLE

N/A

4.67

WS-AI-DQ04360
(WS-AI-DQ04360)

2.4G/5G

Ceiling 
Mount 
Omni

4

7

European Waste Electrical and Electronic 

Equipment (WEEE) Notice

In accordance with Directive 2012/19/EU of the European Parliament on 
waste electrical and electronic equipment (WEEE):

1

The symbol above indicates that separate collection of electrical and 
electronic equipment is required.

2

When this product has reached the end of its serviceable life, it cannot be 
disposed of as unsorted municipal waste. It must be collected and treated 
separately.

3

It has been determined by the European Parliament that there are 
potential negative effects on the environment and human health as a 
result of the presence of hazardous substances in electrical and electronic 
equipment.

4 It is the users’ responsibility to utilize the available collection system to 

ensure WEEE is properly treated.
For information about the available collection system, please contact 
Extreme Customer Support at +353 61 705500 (Ireland).

NCC Statement

(1)

 

「經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅

自變更頻率、加大功率或變更原設計之特性及功能」。

(2)

 

「低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象

時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電

信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學

及醫療用電波輻射性電機設備之干擾」。

(3) 「電磁波曝露量

MPE

標準值

1mW/cm

2

,本產品使用時建議應距離人體:

25

cm

」。

(4)

 

「本器材須經專業工程人員安裝及設定,始得設置使用,且不得直接販售給一般

消費者

Declaration of Conformity in Languages of the 

European Community

Hereby, Extreme Networks, Inc. declares that the radio equipment type 
Wireless LAN Access Point is in compliance with Directive 1999/5/EC. 
The full text of the EU declaration of conformity is available at the 
following Internet address: 

http://www.extremenetworks.com/

ӗ

ӗ૱䈤᰾Җ䱴Ԧ

Supplement to Product Instructions 

䜘Ԧ਽〠

(Parts) 

ᴹ∂ᴹᇣ⢙䍘ᡆݳ㍐

(Hazardous Substance) 

3E

 

+J

 

&G

 

ޝԧ䬜

&U

 

ཊⓤ㚄㤟

3%%

 

ཊⓤҼ㤟䟊

3%'(

 

䠁኎䜘Ԧ

(Metal Parts)

h

ƻ

ƻ

ƻ

ƻ

ƻ

⭥䐟⁑ඇ

(

Circuit Modules)

 

h

ƻ

ƻ

ƻ

ƻ

ƻ

⭥㔶৺⭥㔶㓴Ԧ

(

Cables & Cable Assemblies)

h

ƻ

ƻ

ƻ

ƻ

ƻ

ກᯉ઼㚊ਸ⢙䜘Ԧ

(Plastic and Polymeric parts) 

ƻ

ƻ

ƻ

ƻ

ƻ

ƻ

⭥䐟ᔰޣ

(

Circuit Breakers)

 

ƻ

ƻ

ƻ

ƻ

ƻ

ƻ


ƻ˖

 

㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘൘䈕䜘Ԧᡰᴹ൷䍘ᶀᯉѝⲴਜ਼䟿൷൘

SJ/T 11363-2006   

ḷ߶㿴ᇊⲴ䲀䟿㾱≲ԕлDŽ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is 
below the relevant threshold of the SJ/T 11363-2006 standard. 

 

㺘⽪䈕ᴹ∂ᴹᇣ⢙䍘㠣ቁ൘䈕䜘ԦⲴḀа൷䍘ᶀᯉѝⲴਜ਼䟿䎵ࠪ

SJ/T 11363-2006 

ḷ߶㿴ᇊⲴ䲀䟿㾱≲DŽ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous 
materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard. 


ሩ䬰୞ѻᰕⲴᡰ୞ӗ૱ᵜ㺘ᱮ⽪
ࠟࡋ׋ᓄ䬮Ⲵ⭥ᆀؑ᚟ӗ૱ਟ㜭वਜ਼䘉Ӌ⢙䍘DŽ⌘᜿൘ᡰ୞ӗ૱ѝਟ㜭Պҏਟ㜭нՊਜ਼ᴹᡰᴹᡰࡇⲴ䜘ԦDŽ

This table shows where these substances may be found in the supply chain of

 

Extreme

s electronic 

information products, as of the date of sale of the enclosed product.  Note that some of the component types 
listed above may or may not be a part of the enclosed product. 

 

䲔䶎ਖཆ⢩࡛Ⲵḷ⌘↔ḷᘇѪ䪸ሩᡰ⎹৺ӗ૱Ⲵ⧟؍֯⭘ᵏḷᘇḀӋ䴦䜘ԦՊ
ᴹањн਼Ⲵ⧟؍֯⭘ᵏֻྲ⭥⊐অݳ⁑ඇ䍤൘ަӗ૱к
↔⧟؍֯⭘ᵏ䲀ਚ䘲⭘Ҿӗ૱ᱟ൘ӗ૱᡻޼ѝᡰ㿴ᇊⲴᶑԦлᐕ֌

The Environmentally Friendly Use Period (EFUP) for all enclosed products and their parts 
are per the symbol shown here, unless otherwise marked.  Certain parts may have a 
different EFUP (for example, battery modules) and so are marked to reflect such.  The 
Environmentally Friendly Use Period is valid only when the product is operated under the 
conditions defined in the product manual. 

20 

P/N 9034914-01

Reviews: