background image

5

If you have any questions regarding this product and its safe use, or if there are any missing or damaged parts, DO NOT return Boat Lift Boss

 to the retailer. 

Call the Boat Lift Boss

 Service Department at: 651-357-1862 or e-mail - [email protected]

Boat Lift Boss Installation Guide for 

NuCraft & Craft Lander

PART #: 3005.7216

Extreme Max™ Boat Lift Boss™ Direct Drive Systems are conditionally warranted for consumer use for 2 years after the 
date of retail purchase. Warranty valid only in the USA and Canada. 

Extreme Max™ Boat Lift Boss Direct Drive Systems are conditionally warranted to the original retail purchaser to be free 
from defects in material and workmanship, ordinary wear and tear expected. This warranty shall not apply to any defects 
caused by (I) overloading, (II) physical abuse of goods or any acts of vandalism by any person, (III) improper installation or 
use contrary to the instructions, (IV) commercial use, (V) saltwater use. The sole remedy under this warranty is at the discre-
tion of the manufacturer: the repair of the product by the manufacturer at the manufacturer’s facility, or the replacement of 
the same or similar product. Extreme Max™ is not responsible for any consequential or incidental damages. The consumer 
shall be responsible for shipping charges to return any unit believed to be defective to Extreme Max™. Repaired or replace-
ment units shall be returned to the consumer at the manufacturer’s expense. In the event that a unit is not defective, it will 
be returned to the consumer at the consumer’s expense. Any and all expedited freight charges to handle warranty claims 
are the responsibility of the consumer. Extreme Max™ is not responsible for any 3rd party labor charges that may be in-
curred in removing, transporting or installing the lift.

Extreme Max™ disclaims any other express warranties, all UCC implied warranties, and warranties of merchantability and 
fitness for purpose. 

To expedite warranty service, please complete and return the Warranty Registration Card along with a copy of original retail 
sales receipt at the time of purchase.  

To submit a warranty claim, please send your name, mailing address, original sales receipt and summary of alleged defect 
to [email protected]. Please e-mail or call (651) 357-1862 with questions regarding warranty service and 
claims.

Limited Warranty

If there are any missing or damaged parts, DO NOT return 

Boat Lift Boss™ to the retailer. 

Call the Boat Lift Boss

 Service Dept. at: 651-357-1862 

E-mail - [email protected]

Summary of Contents for Boat Lift Boss 3005.7216






Reviews: