background image

 

2

Introduction 

Congratulations on your purchase of Extech model MM560 or MM570 
digital multimeter. Properly used, this meter will provide many years of 
reliable service. 
 
MultiMaster™ Meters provides high resolution, high accuracy, true rms 
measurements of AC Voltage and Current, DC Voltage and Current, 
AC+DC, Resistance, Frequency, Capacitance, Duty Cycle, dBm, Peak, 
%4-20, Diode, and Continuity. The MultiMaster™ also offers RS-232 PC 
Interface data acquisition capabilities as an option. Model MM570 offers 
dual input Temperature measurements and very wide bandwidth. 

Safety 

International Safety Symbols 

 

!

  Caution !  Refer to the explanation in this Manual 

  Caution !  Risk of electric shock 

 Earth 

(Ground) 

  Double Insulation or Reinforced insulation 

 Fuse 

 

AC, Alternating Current or Voltage 

  DC, Direct Current or Voltage 

 

AC+DC, Current or Voltage 

 

Safety Precautions 

1.  Improper use of this meter can cause damage, shock, injury or death. 

Read and understand this users manual before operating the meter. 

2.  Make sure any covers or battery doors are properly closed and 

secured. 

3.  Always remove the test leads before replacing the battery or fuses. 
4.  Inspect the condition of the test leads and the meter itself for any 

damage before operating the meter. Repair or replace any damage 
before use. 

5.  To reduce the risk of fire or electric shock, do not expose this product 

to rain or moisture. 

6.  Do not exceed the maximum rated input limits. 

Summary of Contents for MultiMaster MM560






















Reviews: