background image

407510-EU-EN-V7.2-5/12 

7

Battery Replacement 

The low battery indication LBT appears on the LCD when the battery runs low. 
To replace the battery: 
1. 

Remove the meter's rubber protective cover to access the rear battery compartment. 

2. 

Remove the battery compartment cover using a small coin or screwdriver and remove the 9V battery. 

3. 

Replace the 9V battery and reinstall the cover and holster. 

You, as the end user, are legally bound (

Battery ordinance

) to return all used batteries and 

accumulators; 

disposal in the household garbage is prohibited!

 

You can hand over your used batteries / accumulators at collection points in your community 
or wherever batteries / accumulators are sold! 

Disposal: 

Follow the valid legal stipulations in respect of the disposal of the device at the end 

of its lifecycle 

Specifications 

General Specifications

 

Circuit 

Custom one-chip LSI microprocessor circuit 

Display 

Dual function 13 mm (0.5") 1999 count LCD w/ contrast adjust 

Measurements Dissolved 

O

2

: mg/l (milligrams per liter); Oxygen in air: %; Temperature: 

°C/°F 

Data hold 

Data hold key freezes displayed reading 

Sensor Structure 

Remote Polarographic Dissolved Oxygen Sensor 

Temperature sensor: Precision thermistor 

Data recording 

Min/Max/Avg readings stored for later recall 

Auto power off 

Meter turns off after 10 minutes 

Sample rate 

0.4 Sec (approx.) 

Data Output 

RS 232 PC serial interface 

Operating conditions 

Temperature: 0 to 50 °C (32 to 122 °F); Humidity: < 80% RH 

Battery power 

9V alkaline battery 

Power Consumption 

Approx. 6.6 mA DC 

Weight 

335 g / 0.74 lbs.(including batteries & probe) 

Dimensions 

Main instrument: 180 x 72 x 32mm (7.1 x 2.8 x1.3") 

Probe: 125 x 20mm (4.9" x 0.8") length/diameter 

Accessories 

Carrying case, 9V battery, and 5 membranes 

Optional accessories 

Membranes, data acquisition software & RS232 interface cable 

Electrical Specifications

 

Measurement Range 

Resolution 

Accuracy 

 

Dissolved Oxygen 

0.0 - 19.9 mg/L 

0.1mg/L 

+ 0.4 mg/L 

Oxygen in air 

0 - 100% O

2

 

0.1 % O

2

 

+ 0.7% O

2

 

Temperature (probe 
only) 

32 to 122 

o

0 to 50 

o

0.1

o

F/C ±1.5 

o

+ 0.8 

o

C  

Temperature (automatic) 

0 to 50

o

C (32 to 122 

o

F) 

Salt 

0 to 39%  

Compensation 
adjustments 

Altitude 

0 to 3900 meters 

Copyright 

©

 2012 Extech Instruments Corporation (a FLIR company) 

All rights reserved including the right of reproduction in whole or in part in any form. 

www.extech.com 

Summary of Contents for 407510








Reviews: