background image

ULTRA VAC

®

Lazer Z

®

HP

Setup Instructions

For Serial Nos. 790,000 & Higher

Loose Parts

Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.

Dealer Pack

Part #

Description

Qty.

Use

Assembling the tubes.

Warranty Registration Reminder

Fill out the online warranty registration
form.

Literature Pack

Part #

Description

Qty.

Use

Manual, Operator’s

1

Manual, Parts

1

Read before operating the machine.

Models and Required Completing Kits

Note:

Use the following charts to verify the kits required for the unit you are installing the UltraVac on.

LHPUV4448

44 inch Deck

Drive Kit

Front Weight Kit*

All Serial Numbers

103-1315

103-5629

48 inch Deck

Drive Kit

Front Weight Kit*

Serial Numbers 203376 & Higher

103-1314

103-5629

LHPUV4650

46 inch Deck

Drive Kit

Front Weight Kit

All Serial Numbers

109-1013

103-5629

50 inch Deck

Drive Kit

Front Weight Kit

All Serial Numbers

109-1014

103-5629

LHPUV5256

52 inch Deck

Drive Kit

Front Weight Kit*

All Serial Numbers

109-1185

103-5629

56 inch Deck

Drive Kit

Front Weight Kit

All Serial Numbers

109-1015

103-5629

* Required on units with a 2 post ROPS installed.

© 2008—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310

Part No. 4500-419 Rev. A

Printed in the USA

All Rights Reserved

Summary of Contents for ULTRA VAC 103-1314










Reviews: