Operation
Drive Wheel Release Valves
Located on the right rear corner of the hydrostatic
pumps.
Drive wheel release valves are used to release the
hydrostatic drive system to allow the machine to be
moved by hand without the engine running.
With a 5/8 wrench, turn both valves one turn
counterclockwise to release the drive system.
Turn clockwise to reset the drive system. Torque to
110-130 in-lb (12-15 N-m).
Do Not overtighten.
Do Not tow machine.
PTO Engagement Switch
Located in the center of the console control below
the Smart Controller (reference Figure 5).
Switch must be pulled out (up) to engage the blades.
Switch is pushed in to disengage the blades.
The LCD indicator will disappear when the PTO
switch is engaged (see Figure 7).
Low Voltage Error
Located on the right console in the message display.
Refer to the
Smart Controller User’s Guide
for
more information.
Deck Lift Handle
Located on the RH of the front control panel.
Pull the handle rearward to raise the cutting deck.
Allow the handle to move forward to lower the
cutting deck to the cut height that has been set.
Pull the handle all the way rearward to latch the
cutting deck into the raised transport position. Pull
rearward and push the button down, on the top of
the lever, to unlatch from transport.
Before Operation
Before Operation Safety
•
Evaluate the terrain to determine what accessories
and attachments are needed to properly and
safely perform the job. Only use accessories and
attachments approved by Exmark.
•
Inspect the area where the machine is to be used
and remove all rocks, toys, sticks, wires, bones,
and other foreign objects. These can be thrown
or interfere with the operation of the machine
and may cause personal injury to the operator or
bystanders.
•
This mower was designed for one operator only.
Do Not carry passengers.
•
Wear appropriate personal protective equipment
such as safety glasses, long pants, substantial
slip-resistant footwear, and hearing protection.
Tie back long hair and avoid loose clothing and
loose jewelry which may get tangled in moving
parts.
•
This machine produces sound levels in excess of
85 dBA at the operator’s ear and can cause hearing
loss through extended periods of exposure. Wear
hearing protection when operating this machine.
•
Check that the following items are in place and in
proper working condition: the operator presence
controls, safety switches, guards, shields, discharge
deflector and/or the entire grass catcher system.
Do not operate the machine unless they are in
proper working condition. Replace worn or
deteriorated parts with genuine Exmark parts
when necessary.
DANGER
It is essential that operator safety mechanisms
be connected and in proper operating
condition prior to use. Contacting the blade
can result in serious personal injury.
Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position. When the key is turned to
the “OFF” position, the engine should shut
off and the blade should stop. If not, stop
using the machine immediately and contact
an Authorized Service Dealer.
•
Do Not operate the mower when people,
especially children, or pets are in the area. Shut
off the machine and attachment(s) if anyone
enters the area.
•
Do Not operate the machine without the entire
grass collection system, discharge deflector,
or other safety devices in place and in proper
working condition. Grass catcher components
are subject to wear, damage and deterioration,
which could expose moving parts or allow objects
to be thrown. Frequently check for worn or
17
Summary of Contents for STARIS S Series
