background image

Maintenance

g038074

Figure 39

Note:

Ensure the oil filter gasket touches the

engine, then an extra 3/4 turn is completed.

Note:

Dispose of the used oil at a recycling

center.

6.

Slowly pour approximately 80% of the specified
oil into the filler tube—use oil recommended in
the

Checking the Engine Oil

section.

g027517

Figure 40

7.

Check the oil level; refer to

Checking the

Engine Oil

section.

8.

Start the engine and check for leaks.

Servicing the Spark Plug

Service Interval: Every 200 hours—Check

the spark plug (Kohler
engine).

Every 500 hours—Replace
the spark plug (Kohler
engine).

Ensure that the air gap between the center and side
electrodes is correct before installing the spark plug.
Use a spark plug wrench for removing and installing
the spark plug and a gapping tool or feeler gauge to
check and adjust the air gap. Install a new spark plug
if necessary.

The spark plug is RFI compliant. Equivalent alternate
brand plugs can also be used.

Type:

Champion XC12YC or equivalent

Air Gap:

0.030 inch (.76 mm)

47

 

Summary of Contents for Radius E Series





















































































Reviews: