Maintenance
engine. Place pan under machine to catch oil.
Remove plug from end of drain hose. Allow oil
to drain and replace oil drain plug. Torque plug
to 20-24 ft-lb.
4. Replace the oil filter every other oil change. Clean
around oil filter and unscrew filter to remove.
Before reinstalling new filter, apply a thin coating
of oil on the surface of the rubber seal. Turn
filter clockwise until rubber seal contacts the filter
adapter then tighten filter an additional 1/2 to
3/4 turn.
5. Clean around oil fill cap and remove cap. Fill to
specified capacity and replace cap.
6. Use oil recommended in engine owner’s manual.
Do Not
overfill. Start the engine and check for
leaks.
Check Hydraulic Oil Level
Service Interval: Every 40 hours
1. Stop engine and wait for all moving parts to stop.
Engage parking brake.
2. Clean area around hydraulic reservoir cap and
remove cap. Oil level should be to the top of the
baffle inside the tank. If not, add oil. Use only
Mobil 1 15W-50 synthetic motor oil. Replace
hydraulic reservoir cap and tighten until snug. Do
Not overtighten.
Note:
The baffle is labeled “HOT” and
“COLD”. The oil level varies with the
temperature of the oil. The “HOT” level shows
the level of oil when it is at 225°F (107°C). The
“COLD” level shows the level of the oil when
it is at 75°F (24°C). Fill to the appropriate level
depending upon the temperature of the oil. For
example: If the oil is about 150°F (65°C), fill to
halfway between the “HOT” and “COLD” levels.
If the oil is at room temperature (about 75°F
(24°C)), fill only to the “COLD” level.
Check Tire Pressures
Service Interval: Every 40 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Check tire pressure in drive tires.
3. Inflate drive tires to 13 psi (90 kPa).
4. Check tire pressure in caster tires.
5. Inflate caster tires to 13 psi (90 kPa).
6. Semi-pneumatic caster tires do not need to be
inflated.
Note:
Do Not add any type of tire liner or foam
fill material to the tires.
Excessive loads created by
foam filled tires may cause failures to the hydro drive
system, frame, and other components. Foam filling
tires will void the warranty.
Check Condition Of Belts
Service Interval: Every 40 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Check under engine deck to check pump drive
belt.
3. Remove left and right belt shields on deck and lift
up floor pan to inspect deck drive belt.
4. For belt adjustment, see the
Pump Drive Belt
and Deck Belt Tension Adjustment
sections.
Lubricate Grease Fittings
Note:
See chart for service intervals.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Lubricate fittings with one to two pumps of
NGLI grade #2 multi-purpose gun grease.
Refer to the following chart for fitting locations
and lubrication schedule.
Lubrication Chart
Fitting
Locations
Initial
Pumps
Number of
Places
Service
Interval
1. Front
Caster wheel
hubs
*0
2
*Yearly
2. Front
Caster
Pivots
*0
2
*Yearly
3. Height
Adjustment
Shaft
Bearings
1
5
40 Hours
4. Deck
Drive Belt
Idler Arm
1
1
Yearly
29
Summary of Contents for Lazer Z HP 465
