Exmark Advantage Series 4500-466 Operator'S Manual Download Page 16

Page: 16 / 60

Specifications

•

Blade Size: (3 ea.)

– 48 inch Deck: 16.25 inches (41.3 cm)

– 52 inch Deck: 18.00 inches (45.7 cm)

– 60 inch Deck: 20.50 inches (52.1 cm)

– 72 inch Deck: 24.50 inches (62.2 cm)

•

Blade Spindles: Solid steel spindles with 1.00 inch
(25 mm) I.D. bearings.

•

Deck Drive:

Electric clutch:

– 48 and 52 inch Decks: “B” Section belt with

self-tensioning idler.

– 60 and 72 inch Decks: 5V Section belt with

self-tensioning idler.

•

Deck:

Full floating deck is attached to out-front support
frame. Anti-scalp rollers provide maximum turf
protection. Deck design allows for bagging,
mulching or side discharge.

– 48 inch Deck: 3 anti-scalp rollers

– 52 inch Deck: 3 anti-scalp rollers

– 60 inch Deck: 4 anti-scalp rollers

– 72 inch Deck: 4 anti-scalp rollers

•

Deck Depth:

– 48 inch Deck: 5.5 inches (14 cm)

– 52 inch Deck: 5.5 inches (14 cm)

– 60 inch Deck: 5.5 inches (14 cm)

– 72 inch Deck: 5.5 inches (14 cm)

•

Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting
height from 1 inch (2.5 cm) to 5 1/2 inches (14
cm) in 1/4 inch (6.4 mm) increments.

•

Mulching Kit: Optional.

Dimensions

Overall Width:

48 inch Deck

52 inch Deck

Without Deck

45.7 inches
(116.1 cm)

Deflector Up

51.8 inches
(131.6 cm)

56.3 inches
(143.0 cm)

Deflector Down

59.6 inches
(151.4 cm)

64.8 inches
(164.6 cm)

60 inch Deck

72 inch Deck

Without Deck

53.0 inches
(134.6 cm)

59.1 inches
(150.1 cm)

Deflector Up

62.5 inches
(158.8 cm)

73.5 inches
(186.7 cm)

Deflector Down

72.8 inches
(184.9 cm)

84.9 inches
(215.6 cm)

Overall Length:

48 inch Deck

52 inch Deck

Roll Bar - Up

79.2 inches
(201.2 cm)

Roll Bar - Down

80.9 inches
(205.5 cm)

60 inch Deck

72 inch Deck

Roll Bar - Up

83.1 inches
(211.1 cm)

86.1 inches
(218.7 cm)

Roll Bar - Down

84.8 inches
(215.4 cm)

87.8 inches
(223.0 cm)

Overall Height:

Roll Bar - Up

Roll Bar - Down

70.5 inches (179.1 cm)

46.8 inches (118.9 cm)

Summary of Contents for Advantage Series 4500-466





























































Search results

Summary of Contents for Advantage Series 4500-466

Reviews:

Brands by name

Popular brands

Exmark Advantage Series 4500-466, Operator'S Manual

Search results

Summary of Contents for Advantage Series 4500-466

Reviews:

Brands by name

Popular brands