EXFO Power Blazer 88200NGE User Manual Download Page 236

Page: 236 / 887

Test Setup - Test Configurator, Timer, and System

226

88000 Series

Interface



Speed

, available with

10/100/1000M Electrical

interface, allows the

selection of the interface rate:

10M

100M

1GE

, or

Auto

. The

negotiated speed will be displayed next to the

Speed

field selection.

The

10M

speed is not available with SyncE test application.



Duplex

choices for

10M

and

100M

electrical interfaces are

Full Duplex

(default),

Half Duplex

, and

Auto

. For other rates the

Duplex is set to

Full Duplex

. Availability of choices depend on the test

applications. Half Duplex is not available with an active copper SFP.
The negotiated duplex will be displayed next to the

Duplex

field

selection.



Flow Control

choices are

Enable TX

Enable RX

Enable RX and TX

None

(default), and

Auto

. When the

Flow Control

is set to

None

pause frames received are ignored. Availability of choices depend on
test applications.



Cable Mode

is available with

10/100/1000M Electrical

interface.

Availability of choices depend on the test application.

Manual

mode is selected when the

Auto-Negotiation

check box is

cleared and allows selecting the type of cable:

MDI

(default) for

straight through cable or

MDIX

for crossover cable.

Automatic

mode is selected when the

Auto-Negotiation

check box is

selected and allows the module to automatically detect the MDI or
MDIX cable type.



Local Clock

is only available with 1GE electrical interface and allows

setting the source of the clock:

Master

(default),

Slave

, or

Auto

1, 3

Auto

is only available when the

Auto-Negotiation

check box is selected.

Slave

is the only available choice for Wander test application.

3. Not available with SyncE test application.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands