manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 495

Test Functions

NetBlazer

483

OH - OTN

Row 2

RES

, columns 1-2, ODU OH: The two Reserved (RES) bytes are 

configurable from 

00

 (default for each byte) to 

FF

. 

PM & TCM

, column 3, ODU OH: The Path Monitoring and Tandem 

Connection Monitoring byte is configurable from 

00

 (default) to 

FF

. 

TCM ACT

, column 4, ODU OH: The Tandem Connection Monitoring 

Activation is configurable from 

00

 (default) to 

FF

. 

TCM6

/

TCM5

/

TCM4

, column 5-13, ODU OH: The Tandem Connection 

Monitoring overhead contains the following bytes. 

The first TCMi byte contains the TTI multiframe byte and is only 
configurable from 

Traces (OTN)

 on page 281.

The second TCMi byte contains the BIP-8 byte and is automatically 
generated for each frame. This byte is not configurable.

The third TCMi byte contains the following sub-fields. This byte is 
configurable from 

00

 to 

FF

. The default value is 

00

 when TCMi is 

disabled, and 01 when enabled.

FTFL

, column 14, ODU OH: The Fault Type Fault Location multiframe 

byte is only configurable from 

FTFL/PT

 on page 146. 

RES

, column 15, OPU OH: The Reserved (RES) byte is configurable 

from 

00

 (default) to 

FF

.  

Bit 1-4

Bit 5

Bit 6-8

BEI/BIAE

BDI

STAT

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands