manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 411

Test Results

NetBlazer

399

Summary (1588 PTP)

GM Info 

Note:

Only available when Grand Master clock information is available. 

The Grand Master Information window displays the decoded clock 
information.

Identity

 report the 8-byte identification code of the Grand Master 

Clock. 

Clock Class

 reports the description and code of the Grand Master 

Clock Class. 

Clock Mode

 reports the description of the Grand Master Clock 

Mode: 

Two-step

 or 

One-step

. 

Start Time

 indicates the time the test was started. 

Code 

Description

0-5, 8-12, 15-51, 53-57, 59-67, 123-132, 171-186, 188-192, 194-215, 
233-247, 249-254

Reserved

6

Sync to primary reference

7, 14

Holdover

13

Sync to application-specific reference

52, 58, 187, 193

Degraded

68 to 79, 81-109 (odd values), 11-122, 133-170, 216-232

Alternate PTP profiles

80-110 (even values)

a

a.

Refer to QL table on page 374 for the list of Quality Level values that will be used as the description.

Quality Level (QL-xxx

a

)

248

Default

255

Slave only

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands