EXFO bv10 User Manual Download Page 111

Page: 111 / 116

Index

BV10-100 and BV10-1000

105

Index

AC/DC power connection ............................ 12
Acronym...................................................... 97
after-sales service ........................................ 86

BrixWorx

Configuring a test for BV10 verifier on Brix-

Worx ...................................... 24

Configuring BV10 for BrixWorx Registry 23
Managing BV10 verifiers........................ 23
Verfier health information ..................... 28

BrixWorx for Turn Up..................................... 2
BV10-100 .................................................... 15
BV10-1000 .................................................. 15

cable ......................................................... 102
caution

of personal hazard................................... 3
of product hazard.................................... 3

certification information ...............................iii
cleaning

front panel............................................. 83
other connectors ................................... 84

CLI command .............................................. 39
CLI session................................................... 37
CLI, introduction ......................................... 29
Command

? ............................................................ 44
clear statistics ........................................ 50
console in-band enable|disable............. 62
console in-band port port_value............ 62
console telnet|ssh server enable|disable61
console telnet|ssh|serial idle-timeout

value_in_seconds.................... 62

exit ........................................................ 45

help ....................................................... 43
interface test laser on|off ...................... 63
interface test transceiver electrical|optical.

CONSOLE..................................................... 16
conventions, safety........................................ 3
customer service.......................................... 90

DC power connection .................................. 12
DEFAULT button .......................................... 21

equipment returns....................................... 90
ESD................................................................ 7
Ethernet OAM Handling test ....................... 79

Summary of Contents for bv10





















































































































Search results

Summary of Contents for bv10

Reviews:

EXFO bv10, User Manual, Page: 111 / 116

Search results

Summary of Contents for bv10

Reviews: