manualshive.com logo in svg

EXFO bv10, User Manual, Page: 30 / 116

Share
Download
EXFO bv10 User Manual Download Page 30

Managing BV10 Verifier on BrixWorx

24

BV10

Configuring a Test

3.

To configure the port of communication, type the following command:

BV10-1000 (DEBUG)>

 server discovery port 

value

 

The default port value is 80. 

4.

To save the new port value, type the following command: 

BV10-1000 (DEBUG)>

 server discovery write

 

Add the BV10 to BrixWorx 

Once you have configured a BV10, you must add it to BrixWorx.

Refer to the BrixWorx User Guide for more information on how to add the 
BV10 Verifier to the BrixWorx system. 

Configuring a Test 

Only a specific set of BrixWorx tests are supported by the BV10 Verifier. All 
tests supported on the BV10 Verifier are available through BrixWorx: 

Ethernet OAM Handling

UDP Echo Responder

TWAMP Light Responder

Smart Loopback

SSH service

Telnet service

Refer to 

Test Applications

 on page 73 for more information on the tests 

supported on the BV10 Verifier.

Summary of Contents for bv10





















































































































Reviews:

No comments