LED Flashes/Chirps Alarm Quick Test
Zone Violation Recall
1
Sensor Full Trigger
-
2
Hood
Hood
3
Door
Door
4
Sensor Warning
Sensor Port Trigger
LED Flashes
Violated Zone
1
Hood
2
Brake
3
Bad tach signal or engine over-rev.
4
BLACK/WHITE wire lost ground
5
3D sensor detected vehicle motion while cranking
6
Received engine stop command (remote, telematics, etc.)
7
Alarm was triggered
8
Run time expired
9
Low vehicle battery voltage detected
1.
Turn the ignition key “ON”, then “OFF”.
2.
Press the valet button
equal to the desired bank (press 2x for Bank 2, etc.)
- This must be done within 5 seconds of step 1.
- The siren/horn will chirp & the status light will fl ash indicating the selected bank (see bank header).
- NOTE: You cannot move from bank to bank. You must start over to change banks.
- NOTE: When accessing BANK 10 (Installer), you will hear a long chirp after 5 presses (User
features). Continue presses 6-10 without delay. You will hear a 2nd long chirp after 10 presses.
3.
Press the valet button
equal to the desired feature’s number.
- The siren/horn will chirp equal to the selected feature.
- Finish presses before hearing any chirps. EXAMPLE: press the valet 5x, then you’ll hear 5 chirps.
4.
Press the transmitter button
(or brake pedal) to select the desired setting.
- 1-BUTTON MODELS: Change the feature by pressing the transmitter button OR brake pedal the same
equal to the desired setting. Complete all presses before hearing any chirps.
- The siren/horn will chirp equal to the selected setting.
5.
Repeat steps 3 & 4
at this time IF you wish to change additional features.
6.
Turn the ignition key “ON” then “OFF”
to exit programming.
- NOTE: The system will exit automatically at any time after 10 seconds of no activity.
INST
ALLER ONL
Y
BANK 10 - Installer Features:
Ignition on, off, press valet 10 times
(2nd Long chirp/fast LED fl ash)
# Feature
Lock Button
(Brake 1x)
Unlock button
(Brake 2x)
Trunk button
(Brake 3x)
Start button
(Brake 4x)
Lock + Unlock
(Brake 5x)
Trunk + Start
(Brake 6x)
1 RS Activation (WHITE/BLUE wire)
1 Pulse
2 pulses
3 pulses
4 pulses
2 Vehicle Learn
Enabled
Disabled
3 Engine Detection
Prog. Voltage
Voltage
Tach Wire
Data-tach
Crank Only
4 Crank Delay (Gas/Diesel)
1.5 sec
15 sec
20 sec
30 sec
5 Light Relay Function
Dome Light
Start
Ignition
Accessory
Status/GWR
Light Flash
6 Blue RS port BLUE Wire
Ignition
Status
0.8 sec Defrost
Pulse
10 min Defrost
Pulse
Pulse After
Engine Off
Horn
7 Crank Time (Tachless/Crank Only) 0.75 sec
1 sec
1.5 sec
2.25 sec
3 sec
Average
8 Door Lock/Unlock Outputs
0.8 sec
3 sec
Double Unlock
Total Closure
9 Remote Start Lock Control
Off
Lock after Start Unlock before Start Lock + Unlock
Lock after
RS Off
10 Turbo Timer
Off
1 min
2 min
3 min
11 Manual Transmission Reservation On - Engine Off
w/ Lock
Off
On - Engine Off w/
Door close (Instant)
On - Engine Off w/
Door close + 10s
12 Data Port Protocol
Green: DBI
Black: DBI
Green: iData
Black: iData
Green: DBI
Black: iData
Green: iData
Black: DBI
13 Alarm Functions
On
Off
Off-Unlock Only
Sensor Detect
14 Pulse Ign. + Acc. on Disarm
On
Off
15 Lock On Prewarn
On
Off
16 Starter Interrupt
Alarm Only
Anti-grind Only
Alarm/Anti-Grind
Automatic
17 Low Temp Crank Extender
0 ms
200 ms
300 ms
400 ms
18 Arm/Disarm or CH. 4/5
Arm/Disarm
Arm/CH. 5
CH. 4/Disarm
CH. 4/CH.5
CH4 Latch/
Disarm
CH4 Latch/CH5
Pulse
19 Horn Relay Function
Horn
Ignition
Trunk Release
Pulse After Start
20 Low Current Mode
On
Off
FEATURE SETTING KEY:
Default Setting
These Are The Defaults For “RS” Models
* Function not available for 1-button remotes. 1-button remotes will use ‘Start x2’ in this setting.
BANK 2 - Low Temp Auto Start:
Ignition on, off, press valet 2 times (3 chirps / 3 LED fl ashes)
# Feature
Valet 1x
Valet 2x
Valet 3x
1 Low Temp Auto Start Threshold
0 Deg F
15 Deg F
32 Deg F
BANK 3 - High Temp Auto Start:
Ignition on, off, press valet 3 times (4 chirps / 4 LED fl ashes)
# Feature
Valet 1x
Valet 2x
Valet 3x
Valet 4x
1 High Temp Auto Start Threshold
75 Deg F
90 Deg F
105 Deg F
120 Deg F
TIP: You can program features via your computer at www.OmegaWeblink.com
Perform Vehicle Learn
(US patent #10,151,289)
AL-XX70B
QUICK REFERENCE
PROGRAMMING GUIDE (FOR FIRMWARE v1.6)
v
isit www.OmegaWeblink.com to get the latest firmware
visit www.OmegaDealer.com to download a complete guide
Programming Features Manually
Features Banks
1.
Enter Bank 10 feature programming
(Installer features - DO NOT SELECT ANY FEATURES).
2.
Press LOCK + UNLOCK
(or BRAKE x 5)
- 1-button/2-button models: Press the START button 5 times
- You will hear a long siren chirp to indicate reset & exit programming.
Features Reset
Tach Wire Signal Learn
Zone Violation Recall:
To diagnose alarm triggers, disarm/unlock the alarm with the remote and the status LED will
fl ash to indicate which zone(s) were triggered last. Turn the ignition key “ON” to clear alarm trigger memory.
If remote start fails to activate, the system will chirp, fl ash the lights, and fl ash the status LED to indicate the
cause
. If remote start shuts down prematurely after successfully starting, you can recall the violation by putting the
system in valet mode (hold the valet button for 3+ seconds). Before the status LED turns on (system in valet mode), the
LED will fl ash to indicate any violated zones.
Programming Transmitters
Alarm Diagnostics
Remote Start Diagnostics
When utilizing the tach wire circuit for engine detection, the vehicle’s tach signal must be learned. Tach signal is learned
during Vehicle Learn and usually does not have to be relearned. Using either method below will automatically change
Installer Feature #3 to ‘Tach Wire’. If a valid tach signal is not detected, the system will not switch to ‘Tach Wire’ mode.
METHOD 1:
1.
Turn the ignition key “ON”
.
2.
Press the brake pedal 5 times
within 5 seconds of step 1.
- The siren/horn will chirp 5 times.
3.
Start the engine.
- The status LED will turn on when it has learned the tach signal. If not, check tach wire & try again.
4.
Press the valet button
to resample the tach signal if needed. If the engine has a high idle at startup, allow the idle to
“settle” around 700 RPM before resampling.
- The status light will fl ash off then back on when the signal has been resampled.
5.
Turn the ignition key “OFF”.
METHOD 2:
1.
Start the engine with the ignition key
.
2.
Press & hold the brake pedal.
3.
Press & release the valet button.
- The siren/horn will chirp 5 times.
- The status LED will turn on when it has learned the tach signal. If not, check tach wire & try again.
4.
Turn the ignition key “OFF” or release the brake pedal to exit.
REMOTE START & SECURITY PERFECTED
CONVENIENCE
SECURITY
BANK 5 - User Features:
Ignition on, off, press valet 5 times (Long chirp/fast LED fl ash)
# Feature
Lock Button
(Brake 1x)
Unlock Button
(Brake 2x)
Trunk Button
(Brake 3x)
Start Button
(Brake 4x)
Lock + Unlock
(Brake 5x)
Trunk+Start
(Brake 6x)
1 Remote Start Run Time
3 min
10 min
15 min
20 min
30 min
2 Flashing Light Confi rmations
Unlock: ON
RS: ON
Unlock: ON
RS: Flash
Unlock: Flash
RS: ON
Unlock: Flash
RS: Flash
3 Confi rmation Chirp Volume
Low
Med-Low
Med-High
High
4 BROWN wire / HORN pulse
BROWN:
Pulse LOW
BROWN:
Pulse MED
BROWN:
Pulse HI
BROWN: Steady
HORN: MED
BROWN: Steady
HORN: Human Panic!
5 Ignition Lock / Unlock
Off
Ign On = Lock
Ign. Off = Unlock Lock + Unlock
6 Door Open Bypass for Feat. #5
On
Off
7 Unlock w/ Trunk Release
On
Off
8 RS Activation (Remote)
Start x 1
Start x 2
Start x 3
Start x 4
Start > 3sec*
Start > 4sec*
9 Last Door Arming
Off
On w/o Lock
On w/ Lock
10 Automatic Rearming
Off
On w/o Lock
On w/ Lock
Enhanced
11 Confi rmation Chirps
Siren + Horn
Siren Only
Horn Only
On Demand
Off
12 Anti-Carjacking
Ignition
Door
Ig Door
Off
13 Override Code
See operation guide for programming instructions. DEFAULT: 1,0
14 Ignition Override
On
Off
15 Alarm Trigger Duration
30 sec
60 sec
90 sec
120 sec
16 Arming Delay
3 sec
15 sec
30 sec
45 sec
17 Open Door Warning Upon Arming On
Off
Vehicle Learn is the ultimate time saver and remote start confi guration tool. It confi gures most
install-critical
features to match vehicle requirements.
IT’S FASTER THAN PROGRAMMING EVEN ONE FEATURE MANUALLY OR ON YOUR PC!
Vehicle Learn Will:
•
Automatically confi gure IGNITION, ACCESSORY, AND START circuits to match the vehicle.
• Let you quickly choose crank delay (NOTE: wait-to-start via data is always honored)
• Sample crank time for crank averaging (tachless modes only).
• Auto-detect engine running method: Data-tach, tach wire (will also tach learn), or tachless mode.
• Auto-detect data port protocols
• Let you quickly enable manual transmission reservation mode.
Before You Begin:
• Make all wire connections
• Connect any accessories/modules to the data ports.
Make sure any interface module/bypass kit is in “DATA MODE” and programmed to the vehicle.
• Set the parking brake if it is connected to the BLACK/WHITE wire for manual transmission.
Vehicle Learn Procedure:
1.
Turn the ignition key ON
(do not start)
2.
Press the valet button 3 times in less than 5 seconds.
- The system will chirp & fl ash lights to indicate crank delay (Default: 1 chirp/fl ash = 1.5 seconds).
3.
(OPTIONAL)
Press valet
to change crank delay.
- Chirp confi rmation: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec.
4.
Start the engine
with the key and let the engine reach a normal idle (about 700 rpm).
AUTOMATIC TRANSMISSION
:
Turn the ignition OFF.
- The system will chirp & fl ash the lights equal the # of IGN/ACC/START circuits detected (Max: 4).
TIP: If you receive fewer chirps/fl ashes than circuits you connected, check connections and try again.
MANUAL TRANSMISSION
:
Release the parking brake
(this completes ignition sequence learn.)
- The system will chirp & fl ash the lights equal the # of IGN/ACC/START circuits detected (Max: 4).
TIP: If you receive fewer chirps/fl ashes than circuits you connected, check connections and try again.
Set the parking brake
again to enter Manual Trans. Reservation Mode option selection (installer feature #11).
- The system will chirp & fl ash the lights to indicate current setting (default: 2 - OFF).
Release & set the parking brake
to scroll through setting options.
- Chirp confi rmation: 1 chirp =
ON
- Shutdown w/ lock, 2 chirps =
OFF
,
3 chirps =
ON
- Shutdown w/ door close, 4 chirps =
ON
- Shutdown 10 sec. after door close.
Before turning the key OFF, perform the selected MT reservation sequence (see operation guide)
- When successful, the LED will once every 2 seconds (ALARM MODELS will fl ash twice every 2 seconds)
5.
PUSH-BUTTON-START VEHICLES: Exit the vehicle & take the OEM fob/key 20 ft. away to allow remote start.
6.
Activate remote start
within 60 seconds of Step 5. Wait until the engine is running and the LED fl ashes slowly.
- The system will then detect data protocols and the best available engine detection method (datatach, tach, etc.).
- If the brake pedal is pressed before the LED fl ashes slowly, settings are reset and you must repeat vehicle learn.
7.
TO SAVE SETTINGS & COMPLETE VEHICLE LEARN:
Press the BRAKE pedal
(the engine will stop).
- This disables VEHICLE LEARN (to enable again, turn on installer feature #2 in bank 10).
TO CANCEL/START OVER:
Press & release the valet button
once.
Scan To Download
the full installation
guide from
OmegaDealer.com!
(login required)
SCAN TO WATCH
HOW-TO VIDEO
SCAN TO WATCH
HOW-TO VIDEO
SCAN TO WATCH
HOW-TO VIDEO
SCAN TO WATCH
HOW-TO VIDEO
Standard Programming:
Use this method to program additional or replacement transmitters.
BEFORE YOU BEGIN:
Have all transmitters which are to operate the system at hand.
1.
Turn the ignition key “ON”
(do not start).
2.
Press the valet button 5 times
within 5 seconds of step 1.
- The horn will briefl y sound
3.
Press & release the “lock” button
on each transmitter one after the other.
- 1-button models, press the “start” button.
- The siren/horn will chirp once for each transmitter.
- NOTE: When the fi rst new transmitter is learned all previous transmitters are erased.
- NOTE: All other button functions will automatically be assigned.
4.
Turn the ignition key “OFF”.
- NOTE: The system will exit automatically at any time after 10 seconds of no activity.
SCAN TO WATCH
HOW-TO VIDEO
SCAN TO WATCH
HOW-TO VIDEO
SCAN TO WATCH
HOW-TO VIDEO
Copyright 2019 Omega Research & Development Technologies, Inc.
QIM_AL-XX70-B_20190605
Alarm Quick Test Mode:
Use this mode to test all zones of the alarm system and quickly adjust any sensors.
1.
Press & hold the valet button
.
2.
Press the Lock button on the remote
within 2 seconds of step 1 (before the system enters valet mode).
- The LED will begin to fl ash rapidly.
3.
Release the valet button
.
- The siren/horn will chirp indicating all alarm zone violations. See the table below.
- NOTE: Chirps will repeat every 2 seconds while the trigger remains violated.
- NOTE: If multiple zones are triggered the chirps will cycle thru the zones every 2 seconds then repeat.
4.
4. Press Lock or Unlock on the controller or power cycle the system to exit.
- NOTE: There is no exit timer to this feature, chirps will continure until the zone is clear or the mode is exited.
SCAN TO WATCH
HOW-TO VIDEO
